Network Security

Here's the output of sh ver on my PIX515E:0: ethernet0: address is 0009.e8bf.6972, irq 101: ethernet1: address is 0009.e8bf.6973, irq 112: ethernet2: address is 0002.b303.b721, irq 11Licensed Features:Failover: DisabledVPN-DES: EnabledVPN-3DES: Disab...

I have a big doubt about what really involves the "Used Memory OID" 1.3.6.1.4.1.9.9.48.1.1.1.5.1 (Cisco Memory Pool Free), because when i try to monitor and graph this OID and the "Free Memory OID (1.3.6.1.4.1.9.9.48.1.1.1.6.1)" in the MRTG, the sum ...

HiI want to setup netmeeting from the outside to the inside interface on a PIX 515E 6.1.(4). Our PIX is setup without any NAT. Which ports do i need to open?

We have a situation here that is confusing us and I am asking for assistance with this one. We have a pix firewall configured with a single outside and two inside interfaces. Behind one of the inside interfaces, we run a Ms Isa server and have severa...

We bought a cisco pix firewall 515 with ios 6.2(2) with pdm version 2.1 running. I have configured this firewall and put it in our production network. I need to configure pdm so that i could browse through the I.E. Can some one advice me what and how...

I have a PIX 515 and many many VPN clients spread across. They connect using VPN 3.1 and above clients (depending on which OS they have). They all have cable modems and none have been having trouble...UNTIL THIS ONE.She is consistently having trouble...

Hello, my problem is the following configuration:VPN Client(Software) --> PIX --> Internet --> PIX (Tunnel Endpoint)The VPN Client cannot connect to the second PIX over the Internet. What must i configure on the first PIX to pass the ipsec traffic to...

Will the wildcard mask in the PIX work to grant access to addresses .82 -.83 and .103-.104?aaa authentication except outbound 10.153.158.49 255.255.255.255 170.206.225.82 255.255.255.252 TACACS+aaa authentication except outbound 10.153.158.49 255.255...

PIX 515 running 6.2We allow any outbound connection. Normal MSN text chatting works fine. Trying to establlish a voice connection doesn't. According to MS you need to allow incoming udp with a source or destination port of 6901. I've done this. Howev...

My problems have been snowballing here. I was attempting to upgrade my PIX OS. I have my PC connected directly to the inside interface of my PIX 515 with a crossover cable. I reloaded the PIX into "monitor" mode and named the interface and gave it an...

I have a pix 515 running dhcp on the ouside interface. When a vpn client behind the pix connect it generates the following error.portmap translation creation failed for protocol 50 src inside <host> to dst <host>g

I have a pix 515 running dhcp on the outside interface. When a vpn client connects from behind the pix it generates error "protmap translation creation failed for protocol 50 src inside <host> to dst <host>.

The PIX 501 will be configured using EZVPN in client mode. But the 501 will be assigned its public IP address by the ISP using DHCP - so this address could change at times. How do I configure the 3030 concentrator, which is the head end of this tunne...

I am having no luck in getting Active X components thru my firewall. I have an application that needs to use this over the web . Windows update starts to download the "windows controls" but hangs. If I'm outside of the firewall it works. If I connect...

I understand that SNMP Informs is an alternative to SNMP traps which can send the information if the acknowledgement is not received for a packet sent. I have a problem here. SNMP Informs sends as many packets as that of the configured retries parame...