Network Security

I'd like to be able to get syslog data from the remote firewall in our environment. We have pix-to-pix vpns connecting them.It doesn't want to work for us and I'm curious if someone's figured a way for it to work.Thanks in advance.....

Dear All,Pix software version 5.3.2Pix 520, Four interfacesINTERNET--Connected to Global Internet only, ISP 193.108.210.1 OUTSIDE--Connected to second ISP 193.173.249.65, from outside to our Webser on the DMZ INSIDE--Users 10.8.0.0, Intranet Server 1...

Below is an error message generated while i'mtrying to ssh into pix (6.1(1)):als@stinky:/usr/src~> ssh -c des pixwarning: Remote server talks SSH-1.5 protocol.Host key not found from database.Key fingerprint:xovib-duziz-cokaz-sobol-dotes-buhud-zahol-...

Looking for a way in which to install a 168 bit DES key on the Cisco PIX 520 ver 5.3(2), without having to reload the code. The only instructions I have been able to locate discuss how to do this at the time of code upgrade, but I want to leave my PI...

Hi There!On a PIX 520, I have three interface cards. OUTSIDE -- Connnected to our ISP 65.203.54.1/24 INSIDE -- A private network 20.0.0.1/24 PRN (DMZ) -- Another firm's (FIRM X) private network 56.238.64.128/26I have a conduit established from the OU...

Is there a way of limiting how many NAT traslation I could statically map to? If yes how do I disable it.I'm trying to troubleshoot a client PIX. It have been configured by somebody before and he gave-up troubleshooting what he configured.My problem ...

Does pix software version 4.2 support ipsec?

I am trying to change static command in pix 520.Currently, I have it set for (static inside, outside 172.16.1.0 172.16.1.0 netmask 255.255.255.0 0 0)This is going to allow 172.16.1.0 network.However, I am running out of 172.16.1.0 network IP.So I hav...

How can I allow all traffic from two DMZ interfaces of my 525 PIX to the inside interface of the PIX and then back from the inside interface to each DMZ? I think I have all of the traffic from the inside to the DMZs working ok but I need to open all ...

is it possible to establish a failover between the pix515 FW and the checkpoint FWI? if yes How? Thanks

I'm trying to establish a W2K pro PPTP tunnel through a PIX out to an external Multi-homed W2K server (across public internet). When I initiate the client (secure side of PIX) it contacts the external server and begins to authenticate but eventually ...

Can Stateful Failover be done WITHOUT the serial failover cable on a PIX with version 6.0? If so how?If not, has anyone extended the cable using a modem, CSU/DSU, or line driver? If so how please be specific (Products used and configuration used)? Th...

Hi All , My client is looking for a software , similar to the ones with Swithch , know the Switch manager , the GUI provided by cisco where you can manage and easily configure the switch .. may that be a 2900 or a 3500 series switch .The same way , i...

outside |PIX --inside - database server |DMZ |Web ServerI can't get the Web Server to communicate with the database server. I can http to the web server from inside,outside. I can http from DMZ to outside. Any ideas?

I have a PIX firewall with registered DNS. The problem is that internal users use the same DNS that the outside world uses. If I put the records on the DNS as unreal IP for the servers, inside user would have no problem but the ouside world will star...