Hi all,I am using the Captive portal on FTD serial 4110 version 6.4.0.7. But I often got Time-out errors when I auth on the website of FTD port 885. I see some refusing bellow. Any know?"[pid 21756:tid 47295284463360] [client 169.254.0.239:34822] Ref...
Forum Posts
We are doing a clean install of version 6.6.1 from 5.4, - We successfully uploaded the img file - Ip address assigned - PKG file uploaded via FTP and system install command applied - After 15 hours the SFR was still in recover mode. ***** EVENT: The...
dear all i have added new ASA5516-FTD-K9 to my network topology as below : and please confirm that is fine too (design) or the place of the asa is correct? ISP --- ASA5516---ISR 2911 router --- 2960 switch ---2960 switch now i need to transfer the wa...
Hi, Any tools are available for sensitive data detection. we have implemented solution but dons have to perform testing to prove if its really working and firewall generating alerts if it sees credit card pattern in request.
Hi, we are enabling Sensitive Data Detection on ASA with FirePOWER module and changes will be applied through FMC. How much resources Its going to consume when we enable this feature , Its 5516 ASA with FirePOWER module and can we get such logs on FM...
I've run into this problem multiple times and there seems to be no common denominator. It happens on different versions, different ASA models (even ASAv), different networks, etc.What happens is this, when I go to issue the ping command, when I star...
Resolved! FMC 2 management port for etherchannel
Hi,we have single FMC device. the requirement is to provide link redundancy for single FMC device. is there any option to do port-channel for 2 management ports.
Resolved! asa NAT and outside interface overlap
I have seen several questions answered similar to this one but not 100% they match exactly? I have setup several ASA's with outside interfaces that have several IP addresses, now I am trying to set one up that only has 1 static public IP on the outsi...
Dear Team , We are facing issue after apply threat intelligence policy - automatic failover happening continuously Cisco FMC is in VM Software version is 6.6.1 Cisco Firepower FTD - 2130 in HA -- Software version is 6.6.1 we came to know that below...
Hello I have a new FTD 2120 I have accessed the ASA with ASDM. I would like to update it, but in the ASDM there is no such option in Device Management menu Also in cli the boot system disk0:/cisco-asa-fp2k.9.12.4.10.SPA is not accepted. What am I ...
Resolved! Computer or User certificate for EAP-TLS
Greetings, When working with EAP-TLS the server (RADIUS) and the client (supplicant) need certificates. On the client side, it is the computer certificate or the user certificate ? Thanks,Edouard.
Hi,We have a couple of 5540s (running 8.0(4) that we use only for remote access (client-to-site) VPNs.In the logs we regularly get some entries similar the following:2009-02-16 11:59:39 UTC Local3.Info x.x.x.x Feb 16 2009 11:59:39: %ASA-6-602101: PMT...
I cannot find information on how to view information about the energy storage of the Firepower 2110. I found 'Power Profilng' is turned off on my device. Perhaps there is a way how you can enable it?
Resolved! connect to ASA
hello,I have a ASA with 3 interface enabled: outside, sub1 and sub2we using sub2 as a management interface, we have acl to permit any traffic between sub1 and sub2.computer from sub 1 ssh login from sub1 interface: successedcomputer from sub 2 ssh l...
Hello, Im looking to get a cisco firewall and place it between my two cisco 9200 switches. Currently I have 7 vlans but will eventually see 20 or so vlans on my switches. the vlans must be able to pass through but I dont plan to connect anything ot...
