Traffic was flowing through this tunnel but recently stopped. When doing a packet-trace on the outside interface using a valid IP from our customer, the following results, and I can't figure out why Phase: 6 denies the flow. Any thoughts? This tunnel...
Forum Posts
Resolved! CISCO ISE using default deny policy
Hello Please help me, my ise policies keep hitting the default deny authorization policy, it was working fine before now i do not know what went wrong. Please see attached screenshots of my policies and my access lists on the switch,Extended IP acces...
Can anyone help me finding the cause of this connections??
Hi! We just install a FMC server on our corporate office. A new branch was open on a different city and they got a FTD-2110...How do I add this remote device to my FMC? I've already did>configure manager add <my.corporate.network.ip> <reg_key>the FTD...
Hi ALL!To better understand my question I first describe what I doing. I migrate from FMC 6.0.1(old where my Firepower Service on ASA is register) to FMC 6.4.0.9 (new virtual machine where I want to migrate my Firepower Service on ASA). I have a ques...
Hi, Try to connect in ssh or https to a cisco asa. We need to manage the firewall by the vpn anyconnect. I'm able to connect to any device in the nertwork but not the firewall. If I try to connect to the management port via vpn I receive this error:...
I have a someone asked this below today... Does following commands on ASA with Firepower make traffic bypass the Firepower inspection?"same-security-traffic intra-interface" for any traffic coming in and going out of the same ASA inside interface."sy...
Resolved! IPSEC
Good morning I tried to install IPSEC on the above mentioned router, but the router does not accept the commands (I REMOVED MY NAMES AND IP ADDRESS):crypto isakmp policy 1hash md5authentication pre-sharecrypto isakmp key XXXXXXXX address X.X.X.X!!cry...
Hi,I would like to ask about can i do MAB for my servers behind the Transparent mode firewall. I would like to run 8021.x and MAB in core switch. Do i need to add ASA BVI Mac-address in MAB table for MAB authentication? let me know can i do MAB for ...
Hi,We buy 2 ASA5545-x with firepower services 2 years ago and it work well in our company.Because there is no internet connection in our network.So we use the classic license to regeist the FIREPOWER service and download the IPS rule every month. an...
Hi, Yes I saw, some people just made the rate high, then there is no warning... is there a table from Cisco about the Rate nummer for the right device? we have installed the Firepower 4115, welch nummer should I configure? regards Robin
I would like to ask why sfr is unresponsive? FIT-ASA# show module sfr details Getting details from the Service Module, please wait...Unable to read details from module sfr Card Type: UnknownModel: N/AHardware version: N/ASerial Number: JAD202200G...
Can someone help me... I have two Cisco ASA 5506... I've already configured the Site to Site VPN connection.......The VPN connection was established like normal........... the problem is, the VPN connection always dropped, and then it will establish ...
Resolved! FS-VMW-2-SW-K9 Specifications
Hi,Anybody knows what CPU, Storage, RAM specifications required for vm to install FireSight Management Center FS-VMW-2-SW-K9? Thanks.
Resolved! Cisco ASA Capture Meaning
Hello, I would like to know the meaning of these words (P0/P2) in an ASA capture: CISCOASA# capture TOTO interface Guest real-time4: 11:04:48.898055 802.1Q vlan#XXXX P2 172.22.X.X.50336 > X.X.X.X.53: udp 395: 11:04:48.908034 802.1Q vlan#XXXX P0 172.2...
