For three months I have had issues with a production terminal server (2012 release two) for a 65 user profile install. The terminal server disconnects users and does not permit login to the console nor via the network until the Virtual Machine is re...
Forum Posts
Hello I am on FMC 6.2.3, for visibility purpose (data usage etc) our initial deployment was such that every Site (Firewall) was configured as a separate domain. We are nearing the limit of 50 domains, obviously there are many others "sites" (Firewall...
Hi, My inter-chassis cluster giving an error on FMC "interface port-channel is not receving any packets" its alerting for 2nd unit in the cluster. I have done trubleshooting and can't find any communication issue but after a certain time it start ale...
Hi.. I have been running cisco ASA 5545 X with firepower module installed, it has two storage device with model number- Micron_M600 ( not sure if it is SSD). However firepower module has setup and is showing up(ver 6.2.0).I will be going to build FMC...
Guys hi! In previous post I had successfully create "outside-dmz-inside" network. It works, but not good. When I try connect from PC (10.17.20.3) in inside-subnet to GW-PC (10.17.19.1) in dmz-subnet RDP connects but in 5-25 sec my connection teardown...
hello everyone i want to allow all the trafiic coming from the subnet(192.168.10.0/24) connected to outside interface going to the subnet(10.30.30.0/24) connected to ninside interface please help me i tried all the ways but still havent yet go...
Dear community, it's high time I created an account here. I've recently purchased a Cisco ASA 5520 and wanted to boot it / wipe it.However, the status light is constantly amber and, while the management port lights up with an ethernet cable, I have n...
Hi Folks, I have been trying to configure multiple access-group in same interface in asa Version 9.1(5)16. But, i am able to configure only on access-group per interface. Can you please clarify me that, how many access-group can be configured per int...
Hy! I have a 5506 Firwall which is about 1 year old. Last week we had to make a restart and now when i put in the power cable i only have a red light flashing and the firewall won´t start. Also when i try to connect via console i will get no answer? ...
Resolved! IKEv2 VPN working without NAT exemption
I'm trying out the setup of a static to dynamic IKEv2 IPsec VPN. The VPN is working, and pings from the client PC 2 in the image below (192.168.2.2) are successfully making their way to the client PC 1 in the topology. ISAKMP and IPsec SA stats are ...
There have been problems with Ransom ware sites,we have list of site IP address that cause problems, so that is easy to add to a black list groupbut some locations are only known by their FQDN from certain Domain serversso we blocked that Domain serv...
Security Intelligence Events shows https://www.microsoft.com as being URL blocked and classified under Security Intelligence Category as "URL Malware." Is Firepower's Collective Security Intelligence (CSI) URL blocking Microsoft.com?
Hello Support, I have a question in regards to accessing the http interface of the logical device created in the FirePower chassis. I created the logical device, but cannot access the http web page. It reads as blank. I am able to SSH to this without...
hi,i'll be configuring AAA on our FWs and need to confirm if this single command line for AAA accounting is enough to log the executed commands to ISE: aaa accounting command <ISE-GROUP-NAME> or just these two? aaa accounting command privilege 1 <ISE...
Resolved! End of Service for ASA5515-SSD120-K9
Hello there. We currently have a ASA5515-SSD120-K9 we purchased for use with CX bundle. Cisco marked this model of firewall for end of service in August 2020 and encourage to migrate to Firepower. We migrated this CX to firepower some time ago using...
