Greetings I'm trying to understand why our FMCv is so slow to operate. I've had a TAC on the issue but the technician wasn't very straight wether or not I have a hardware design issue or if there is something that needs to be optimized on the FMC. So...
Forum Posts
There may be something wrong with the firepower because the physical port is not active when connected directly. I'm going to restore the firepower. But it cannot be restore in the firepower command. How can I exit the firepwer os?
I have some queries, We are going to implement/insstall a new Cisco ASA 5506-X Configuration device in our environment: Requirement: We have 1 vodafone ISP link with public IP (50.50.50.1/30- Lets assume) that would drop on outer interface of ...
Hi, I'm Joseph.I'm using an ASA5540 firewall router to Connect my LAN to my ISP, the LAN is on the inside interface of the router while the ISP is on the outside interface. From my LAN I can ping the inside interface but I can't ping the outside inte...
Hi all, Im looking at something interesting and would like to have your opinion on this. I have 2 sites , to both these sites there will be remote VPN users. On top of this there will be a replication requirement. now at the sites, for 1 site ISP c...
Dears, I m having confuison is cisco security products, Cisco AMP called as a sandboxing ??? Is it Cisco sandboxing does exclusive which AMP is not performing. What does threat Grid does ?? what exclusive it does from AMP, Sandboxing
Resolved! ASA 5516-X with SPA122 SIP not working
Since I've upgraded from the ASA5505 to the ASA5516-X, my Voip adapter no longer works. It worked fine with my old ASA5505 but not since I've upgraded.My VOIP adapter is a SPA122 from Cisco. It's communicating via UDP on port 5060. The settings on...
Resolved! Firewall between DC and DR
Hi, I need suggestion, we have Data Center and Disaster Recovery connected with point to point link. link is connection our DC sever segment with DR server segment. It is mainly for replication of data. in future VM, vlan extension is possible. No...
Background: I'm using ASA 5506-X version 9.8.2 with FirePower moduleIt has inside a BVI address on the inside of 192.168.2.1 /24 which gives that out to all inside interface automatically. The outside interface is connected to the internet and can ...
I have ASA5506-X (9.8.2) with firepower services. I'm working on the initial set up of firepower and am confused on how the IP addressing should be done. The ASA has already be configured with BVI / all inside interfaces set to 192.186.2.1 (which is ...
Saving your changes:For an ASA with firepower services, if you make a change to firepower CLI configuration such as change IP address in it or something like that, does the change get saved automatically even if you power cycle, or do you need to typ...
I only know how to manage the firewall through the GUI ASDM. now it's not working since last firefox update. I tried other browsers but nothing helps. I get this message in every browser .. Cisco ASDM 5.2 - Error "Cisco ASDM 5.2 encountered loadin...
Resolved! NTP server and & DHCPD OPTION 4 on ASA
On ASA 5506-X version 9.8.2, I have configured NTP:NTP server x.x.x.x source outside(Where x.x.x.x is an external public NTP server ip address). I also configured timezone on the ASA as I read it should be relatively close to the NTP time, though not...
It's day two of the adobe zero day with a exploit code in the wild. CVE-2018-15982 is yet to be discussed at Cisco Talos, and: For that matter the suspect C2 IP isn't even published, thus our FTD identifies the address as still: "Risk Unknown". But ...
Resolved! Dynamic state rules
Hello all,I have a question regarding the dynamic state of a Policy rule: If i create a dynamic state that disable that rule for 10 minutes if the source is 192.168.1.1 after 3 counts, does this new state apply to all source & destination or only th...
