01-23-2005 12:18 AM - edited 02-20-2020 11:53 PM
I want to update my pix from 4.4(7) to 6.x.And it requires my pix520 to have at least 16M flash and 32M RAM.
But I'm not sure the flash size of my pix520.
which command should I use?
Solved! Go to Solution.
01-23-2005 09:51 PM
Check in the FAQ at this link
How do I determine how much Flash memory my PIX has?
A. If you perform a show version command on your PIX, and the Flash size is not given in MB, then use the table below to see how much Flash your PIX has.
i28F020 512 KB
AT29C040A 2 MB
atmel 2 MB
i28F640J5 8 MB - PIX 506 16 MB - all other PIXes
strata 16 MB
For example, if your show version command output looked like this:
Cisco Secure PIX Firewall Version 5.1(1)
Compiled on Fri 01-Oct-99 13:56 by pixbuild
pix515 up 4 days 22 hours 10 mins 42 secs
Hardware: PIX-515, 64 MB RAM, CPU Pentium 200 MHz
Flash i28F640J5 @ 0x300
BIOS Flash AT29C257 @ 0xfffd8000
0: ethernet0: address is 00aa.0000.0037, irq 11
1: ethernet1: address is 00aa.0000.0038, irq 10
2: ethernet2: address is 00a0.c92a.f029, irq 9
3: ethernet3: address is 00a0.c948.45f9, irq 7
Licensed Features:
Failover: Enabled
VPN-DES: Enabled
VPN-3DES: Disabled
Maximum Interfaces: 6
Serial Number: 123 (0x7b)
Activation Key: xxxx
The amount of Flash memory is 16 MB.
Cheers,
Paul.
01-23-2005 05:36 AM
Use show version command to get this information.
Hope this helps.
01-23-2005 08:33 PM
In the show version command output,I'm not sure which line indicates the flash size?
01-23-2005 09:51 PM
Check in the FAQ at this link
How do I determine how much Flash memory my PIX has?
A. If you perform a show version command on your PIX, and the Flash size is not given in MB, then use the table below to see how much Flash your PIX has.
i28F020 512 KB
AT29C040A 2 MB
atmel 2 MB
i28F640J5 8 MB - PIX 506 16 MB - all other PIXes
strata 16 MB
For example, if your show version command output looked like this:
Cisco Secure PIX Firewall Version 5.1(1)
Compiled on Fri 01-Oct-99 13:56 by pixbuild
pix515 up 4 days 22 hours 10 mins 42 secs
Hardware: PIX-515, 64 MB RAM, CPU Pentium 200 MHz
Flash i28F640J5 @ 0x300
BIOS Flash AT29C257 @ 0xfffd8000
0: ethernet0: address is 00aa.0000.0037, irq 11
1: ethernet1: address is 00aa.0000.0038, irq 10
2: ethernet2: address is 00a0.c92a.f029, irq 9
3: ethernet3: address is 00a0.c948.45f9, irq 7
Licensed Features:
Failover: Enabled
VPN-DES: Enabled
VPN-3DES: Disabled
Maximum Interfaces: 6
Serial Number: 123 (0x7b)
Activation Key: xxxx
The amount of Flash memory is 16 MB.
Cheers,
Paul.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide