cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1192
Views
0
Helpful
4
Replies

FXO and Rauland system integration

douglas.wolf
Level 1
Level 1

I am trying to integrate an FXO card on a 1750 router to go into a Rauland Telecenter 21 master port for paging control.

I have a route pattern configuration of 3054 (the extension I want to dial to reach the Rauland), set to my restricted partition, set to route the pattern, and set to the appropriate gateway that the FXO card is installed in. Am I doing something wrong? what should my config look like on the 1750?

4 Replies 4

jkoniecki
Level 1
Level 1

Douglas,

Can you post your show version and show run ?

Have you ever made any calls out of this 175X router ?

Jk

The 1750 used to have an fxs in it, worked fine. Replaced with FXO, but I'm not convinced that there isn't something else I'm supposed to configure.

Thanks for the help --

Here's the show run:

User Access Verification

Password:

MS-Gateway_251>en

Password:

MS-Gateway_251#show run

Building configuration...

Current configuration : 1155 bytes

!

version 12.2

no service single-slot-reload-enable

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname MS-Gateway_251

!

logging rate-limit console 10 except errors

enable password

!

memory-size iomem 25

ip subnet-zero

no ip finger

!

no ip dhcp-client network-discovery

call rsvp-sync

!

!

!

!

!

!

!

!

interface FastEthernet0

ip address 10.1.0.251 255.255.0.0

speed auto

!

ip classless

ip route 0.0.0.0 0.0.0.0 10.1.0.1

no ip http server

!

!

voice-port 0/0

!

voice-port 0/1

!

voice-port 2/0

timeouts interdigit 5

description FXO

station-id name 3054

station-id number 3054

!

voice-port 2/1

timeouts interdigit 5

description FXO

station-id name 3055

station-id number 3055

!

dial-peer voice 10 voip

incoming called-number .

destination-pattern .T

session target ipv4:10.1.4.1

dtmf-relay h245-alphanumeric

codec g711ulaw

fax rate disable

ip precedence 5

no vad

!

dial-peer voice 22 pots

destination-pattern 3054

port 2/0

!

dial-peer voice 23 pots

destination-pattern 3055

port 2/1

!

!

line con 0

transport input none

line aux 0

line vty 0 4

password thinmint

login

!

end

MS-Gateway_251#

HERE's the show ver:

MS-Gateway_251#show ver

Cisco Internetwork Operating System Software

IOS (tm) C1700 Software (C1700-SV3Y-M), Version 12.2(1), RELEASE SOFTWARE (fc2)

Copyright (c) 1986-2001 by cisco Systems, Inc.

Compiled Fri 27-Apr-01 08:47 by cmong

Image text-base: 0x800080E0, data-base: 0x80A59274

ROM: System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)

MS-Gateway_251 uptime is 2 days, 6 hours, 13 minutes

System returned to ROM by power-on

System image file is "flash:c1700-sv3y-mz.122-1.bin"

cisco 1750 (MPC860) processor (revision 0x601) with 24576K/8192K bytes of memory

.

Processor board ID JAD05030ME4 (2974950972), with hardware revision 0000

M860 processor: part number 0, mask 32

Bridging software.

X.25 software, Version 3.0.0.

1 FastEthernet/IEEE 802.3 interface(s)

4 Voice FXO interface(s)

32K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

MS-Gateway_251#

baysjohn
Level 1
Level 1

Where's the FXS device that you will be using to dial? FXO is the Office side, so an Office to Office link can be set, but there needs to be a FXS (handset) somewhere to activate the FXO trunk. If you're plugging a regular phone into the FXO port, this wont work, you need an FXS port on your 1750.

The rauland side willa ct as the FXS and provide battery and dial tone.