05-28-2015 05:51 PM - edited 03-03-2019 07:52 AM
Actually, I already posted about WS-SUP720-3B.
But, at that time, The problem is the SP. I could see through the show version.
However,, I have another SUP. and I booted up it.
It was continuously entering the ROMmon mode...
So, I was also continuously manually booting the SUP.
------------------------------------------------------------------------------------------------------------------------------
I inserted flash memory in the disk0 slot..
I performed below commands one by one.
boot system flash disk0:s72033-ipservicesk9_wan-mz.122-18.SXF16.bin
boot system disk0:s72033-ipservicesk9_wan-mz.122-18.SXF16.bin
AND rebooting?
I could see the ROMmon...
rommon 1 >
------------------------------------------------------------------------------------------------------------------------------
I upload "show version", "remote command switch show bootvar", "show bootvar".
and I also upload rommon 1 > dir disk0: which is a evidence to be stored IOS.
After you show uploaded photos, plz give me a good idea....
Thank you:)
Cheers.
Edited...
Although I input command "boot system disk0: ~ " and "write memory",
and rebooting, => there is no command boot system disk0: ~ in the show run...
About this, you can see the boot_system_disk0.png
ah.. It is very difficult.. hard work
05-28-2015 09:44 PM
can you post the output of "dir" once router is booted (i.e. in # prompt)
05-28-2015 10:02 PM
05-28-2015 10:20 PM
Save the config after below and reload.
!
config t
boot-start-marker
boot system flash disk0:s72033-ipservicesk9_wan-mz.122-18.SXF16.bin
boot system flash bootflash:
boot-end-marker
end
wr
!
05-28-2015 10:26 PM
Oh Ok I'll give it a try and let you know whether it is working properly or not :)
05-28-2015 10:42 PM
Also, your SP shows incorrect config-reg. Pls change it:
(config)# remote command switch config-reg 0x2102
05-28-2015 10:54 PM
First of all, I did
boot system flash disk0:s72033-ipservicesk9_wan-mz.122-18.SXF16.bin
boot system flash bootflash:
By the way,
Is is right there is no command "boot-start-marker", "boot-end-marker".
Anyway, I did 2 commands
boot system flash disk0:s72033-ipservicesk9_wan-mz.122-18.SXF16.bin
boot system flash bootflash:
and "wr"
and "reload"
again rommon mode...
now I'm trying to input "remote command switch config-reg 0x2102"
05-28-2015 11:19 PM
05-28-2015 11:29 PM
Ok, but the problem is your SP config-reg is not correct (see the output of remote command switch show bootvar). Try once more with:
!
config-register 0x2102
wr
!
and then check the outputs of:
# show bootvar
# remote command switch show bootvar
05-29-2015 12:01 AM
I did!!
first. remote command switch show bootvar
second. config-register 0x2102
third. show bootvar
fourth. remote command switch show bootvar
I tried upper procedures...ㅠㅠ
I really don't know why it is not stored that I input?
I definitely input config-register 0x2102 and boot system disk0:s72033-ipservicesk9_wan-mz.122-18.SXF16.bin and wr .
and I turn it off and turn it on. but there is no command boot system disk0:~ in the show run although I input "write" command...
...Please teach me how to solve it!...
Please reply as soon as possible .. if possible!
I continuously keep an eye your reply!!
05-29-2015 12:25 AM
Have tried reboot after "fourth.png" ??
05-29-2015 12:43 AM
05-30-2015 06:44 PM
Anything else I should do to solve??..
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide