07-03-2004 06:40 AM - edited 03-02-2019 04:49 PM
hi i am tring to configure ISDN line on Cisco803 router's between two location however i am not able to make connection , please have look on thr config and advise me
thankyou
router 1
exhibition#show config
Using 977 out of 8078 bytes
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname xxxx
no logging on
enable secret xxxxxx
!
!
!
ip subnet-zero
!
isdn switch-type basic-net3
!
!
!
interface Ethernet0
ip address 192.168.3.1 255.255.255.0
!
interface BRI0
ip address 192.168.1.2 255.255.255.0
encapsulation ppp
dialer wait-for-carrier-time 60
dialer map ip 192.168.1.3 name main broadcast 17218515
dialer-group 1
isdn switch-type basic-net3
isdn twait-disable
isdn autodetect
ppp multilink
!
interface Dialer0
no ip address
encapsulation ppp
dialer in-band
dialer idle-timeout 300
dialer hold-queue 10
dialer load-threshold 150 outbound
dialer-group 1
ppp authentication pap
ppp multilink
!
ip classless
ip route 192.168.2.0 255.255.255.0 192.168.1.3
ip http server
!
!
dialer-list 1 protocol ip permit
!
line con 0
stopbits 1
line vty 0 4
login
!
no rcapi server
router 2
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname xxxx!
no logging on
enable secret xxxxx
!
!
!
ip subnet-zero
!
isdn switch-type basic-net3
!
!
!
interface Ethernet0
ip address 192.168.2.1 255.255.255.0
!
interface BRI0
ip address 192.168.1.3 255.255.255.0
encapsulation ppp
dialer wait-for-carrier-time 60
dialer map ip 192.168.1.2 name main broadcast 17298296
dialer-group 1
isdn switch-type basic-net3
isdn twait-disable
isdn autodetect
ppp multilink
!
interface Dialer0
no ip address
encapsulation ppp
dialer in-band
dialer idle-timeout 300
dialer hold-queue 10
dialer load-threshold 150 outbound
dialer-group 1
ppp authentication pap
ppp multilink
!
ip classless
ip route 192.168.3.0 255.255.255.0 192.168.1.2
ip http server
!
!
dialer-list 1 protocol ip permit
!
line con 0
stopbits 1
line vty 0 4
login
!
no rcapi server
!
!
,
07-03-2004 08:43 AM
Hello,
you need to add the following to both routers (the routernames might actually differ form what you have, the password as well, but it must be the same on both sides):
Router 1
username R1 password 0 cisco
interface Dialer 0
ppp pap sent-username R1 pasword cisco
Router 2
username R2 password 0 cisco
interface Dialer 0
ppp pap sent-username R2 pasword cisco
HTH,
Georg
07-09-2004 10:25 AM
A quick correction: that snippet should read:
Router 1
username R2 password 0 cisco
interface Dialer 0
ppp pap sent-username R1 password cisco
Router 2
username R1 password 0 cisco
interface Dialer 0
ppp pap sent-username R2 password cisco
There must be a username/password entry on each router for the username and password sent by the _other_ router. And both routers must agree on the password they are using with each other ("cisco" in this case). Also be aware that there need to be two "s"s in password :-).
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide