Hi,I have unexpectedly deleted ios image and when i rebooted the router it went to rommon prompt. Now i have downloaded the ios image. How can i transfer it to router and get it up.
Hi,I have unexpectedly deleted ios image and when i rebooted the router it went to rommon prompt. Now i have downloaded the ios image. How can i transfer it to router and get it up.
except the welcome message of a router, any other usage of the MOTD?is it complusory in come countries?will it be harmful if I don't use the MOTD and mount the router on internet?
hi i am tring to configure ISDN line on Cisco803 router's between two location however i am not able to make connection , please have look on thr config and advise methankyourouter 1exhibition#show configUsing 977 out of 8078 bytes!version 12.2no ser...
I have two routers connected via load-sharing PVCs. IP (other thatEIGRP) between the 2 routers works fine. The IP addresses of the"connected" interfaces (& EIGRP peers) are correctly subnetted & inthe the same subnet. However, I get the following er...
Hi,I have Windows 2003 Cluster server with two NICs, and virtual IP address. Server is connect to 6513 switch. NIC1 IP address is 192.168.102.227 NIC2 IP address is 192.168.102.228 and the Virtual IP address is 192.168.102.232. I can ping NIC1 and NI...
Dear all,Need your adviceI have a Cisco1721 with 2 ADSL and 1 FEand both connected ISP with NAT for outgoing traffic.I want to use route-map for outgoing traffic via ADSLHow does Nat failover to another Nat entry after link failover?as attached. hope...
Hello,I'm wondering how many IPv6 over IPv4 tunnels, including manually configured, 6to4 and GRE are supported in Cisco routers?Thanks.Yongjun.
Hi,We have a setup with 2 x WS-C3750G-12S-E connected through Copper 100 Fastethernet (using GLC-T SFP) connection to 2 remote locations. After rebooting those switches, the copper links stay down (no issue with the fiber connection). We have to manu...
I'm trying to setup some kind of notification to occur when a downstream switch loses connectivity and would really appreciate any advise on the matter.Here's a very rough diagram of my current setup:core-6500 | |-- distribution-3550 | ...
We have a network with 27 Cat3548XL switches and a C4006 as a core switch. Since 2 days ago, the CPU of the C3548XL have been increased to limits more than 80%. We have issued the command "sh proc CPU" and observe that the process "ARP Input" has 23,...
In the network we are having a problem since a week ago. Some PC can not get a valid IP adress automatically, but using release command and renew command several times it gets the IP adress.Some times the adress is duplicated.The problem is not affec...
In the network we are having a problem since a week ago. Some PC can not get a valid IP adress automatically, but using release command and renew command several times it gets the IP adress.Some times the adress is duplicated.The problem is not affec...
I have a 2600XM router acting as an OSPF DR. This holds 147 routes. 46 are Intra area routes and 101 are External type-1. The router is running IOS ver 12.2(8)T5 with 32mb DRAM. This peers with 8 neighbours.Everytime I add static routes on a fire...
I installed the 5 parts of the LMS. Following instrauctions when I tested the Campus Manager installation I received a java error I/O Error loading aborted. Any workarounds for this? W2K server with 2 processors and 1.6GB Ram.Java does not work in an...
Hi All,I would like to know a 6509 MSFC2/Sup II Engine ( WS-X6K-SUP2-2GE ) is compatible on a 6000 chasis.Will it work ok on a 6000 chasis ? Are they going to be any problems or what are the most typical problems when doing this.What should I be awa...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM |