Help with Booting issue

amakinde · ‎03-04-2002

Please find below is what i have don and what am seing when i boot in the my router.System Bootstrap, Version 5.2(5), RELEASE SOFTWARE

2500 processor with 16384 Kbytes of main memory

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(5), RELEASE SOFTWARE

(fc1)

Compiled Thu 23-Mar-95 02:08 by kmac

Image text-base: 0x01020000, data-base: 0x00001000

cisco 2500 (68030) processor (revision D) with 16380K/2048K bytes of memory.

Processor board serial number 02095900

X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.

Authorized for Enterprise software set. (0x0)

1 Ethernet/IEEE 802.3 interface.

2 Serial network interfaces.

32K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read/Write)

--- System Configuration Dialog ---

At any point you may enter a question mark '?' for help.

Refer to the 'Getting Started' Guide for additional help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Would you like to enter the initial configuration dialog? [yes]: n

Press RETURN to get started!

Router(boot)>en

Router(boot)#copy start run

^

% Invalid input detected at '^' marker.

Router(boot)#cpoy run

^

% Invalid input detected at '^' marker.

Router(boot)#copy run start

^

% Invalid input detected at '^' marker.

Router(boot)#erase

% Incomplete command.

Router(boot)#reload

Proceed with reload? [confirm]

System Bootstrap, Version 5.2(5), RELEASE SOFTWARE

2500 processor with 16384 Kbytes of main memory

--- System Configuration Dialog ---

At any point you may enter a question mark '?' for help.

Refer to the 'Getting Started' Guide for additional help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Would you like to enter the initial configuration dialog? [yes]: n

No usable interfaces

System Bootstrap, Version 5.2(5), RELEASE SOFTWARE

2500 processor with 16384 Kbytes of main memory

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(5), RELEASE SOFTWARE

(fc1)

Compiled Thu 23-Mar-95 02:08 by kmac

Image text-base: 0x01020000, data-base: 0x00001000

cisco 2500 (68030) processor (revision D) with 16380K/2048K bytes of memory.

Processor board serial number 02095900

X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.

Authorized for Enterprise software set. (0x0)

1 Ethernet/IEEE 802.3 interface.

2 Serial network interfaces.

32K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read/Write)

--- System Configuration Dialog ---

At any point you may enter a question mark '?' for help.

Refer to the 'Getting Started' Guide for additional help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Would you like to enter the initial configuration dialog? [yes]:

Press RETURN to get started!

Router(boot)>

Router con0 is now available

Press RETURN to get started.

Router(boot)>en

Router(boot)#erase

% Incomplete command.

Router(boot)#erase flash

System flash directory:

No files in System flash

[0 bytes used, 8388608 available, 8388608 total]

Erase flash device? [confirm]

Are you sure? [yes/no]: y

Erasing device... eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee ...erased

Router(boot)#copy run start

^

% Invalid input detected at '^' marker.

Router(boot)#en

Router(boot)#copy run start

^

% Invalid input detected at '^' marker.

Router(boot)#copy run start

^

% Invalid input detected at '^' marker.

Router(boot)#show version

Cisco Internetwork Operating System Software

IOS (tm) 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(5), RELEASE SOFTWARE

(fc1)

Compiled Thu 23-Mar-95 02:08 by kmac

Image text-base: 0x01020000, data-base: 0x00001000

ROM: System Bootstrap, Version 5.2(5), RELEASE SOFTWARE

Router uptime is 18 minutes

System restarted by power-on

Running default software

cisco 2500 (68030) processor (revision D) with 16380K/2048K bytes of memory.

Processor board serial number 02095900

X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.

Authorized for Enterprise software set. (0x0)

1 Ethernet/IEEE 802.3 interface.

2 Serial network interfaces.

32K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x2142

Router(boot)#

€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€

€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€ø

Press RETURN to get started!

Router(boot)>copy nvram

^

% Invalid input detected at '^' marker.

Router(boot)>show version

Cisco Internetwork Operating System Software

IOS (tm) 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(5), RELEASE SOFTWARE

(fc1)

Compiled Thu 23-Mar-95 02:08 by kmac

Image text-base: 0x01020000, data-base: 0x00001000

ROM: System Bootstrap, Version 5.2(5), RELEASE SOFTWARE

Router uptime is 2 minutes

System restarted by power-on

Running default software

cisco 2500 (68030) processor (revision D) with 16380K/2048K bytes of memory.

Processor board serial number 02095900

X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.

Authorized for Enterprise software set. (0x0)

1 Ethernet/IEEE 802.3 interface.

2 Serial network interfaces.

32K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x1402

Router(boot)>reload

Translating "RELOAD"...domain server (255.255.255.255)

% Unknown command or computer name, or unable to find computer address

Router(boot)>sh ver

Cisco Internetwork Operating System Software

IOS (tm) 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(5), RELEASE SOFTWARE

(fc1)

Compiled Thu 23-Mar-95 02:08 by kmac

Image text-base: 0x01020000, data-base: 0x00001000

ROM: System Bootstrap, Version 5.2(5), RELEASE SOFTWARE

Router uptime is 6 minutes

System restarted by power-on

Running default software

cisco 2500 (68030) processor (revision D) with 16380K/2048K bytes of memory.

Processor board serial number 02095900

X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.

Authorized for Enterprise software set. (0x0)

1 Ethernet/IEEE 802.3 interface.

2 Serial network interfaces.

32K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x1402

Router(boot)>sh run

Router(boot)>en

Password:

% Bad secrets

Router(boot)>en

Password:

% Password timeout expired!

Password:

% Password timeout expired!

% Bad secrets

Router(boot)>en

Password:

% Bad secrets

Router(boot)>en

Password:

% Bad secrets

Router(boot)>en

Password:

% Bad secrets

Router(boot)>config t

^

% Invalid input detected at '^' marker.

Router(boot)>\config t

^

% Invalid input detected at '^' marker.

Router(boot)>config t

^

% Invalid input detected at '^' marker.

Router(boot)>copy run start

^

% Invalid input detected at '^' marker.

Router(boot)>show st

Router(boot)>show stacks

Minimum process stacks:

Free/Size Name

1572/2000 Init

Interrupt level stacks:

Level Called Free/Size Name

3 0 1000/1000 Serial interface state change interrupt

4 2 932/1000 Network interfaces

5 3475 958/1000 Console Uart

Router(boot)>show context

^

% Invalid input detected at '^' marker.

Router(boot)>show context

^

% Invalid input detected at '^' marker.

Router(boot)>?

Exec commands:

connect Open a terminal connection

disconnect Disconnect an existing network connection

enable Turn on privileged commands

exit Exit from the EXEC

help Description of the interactive help system

login Log in as a particular user

logout Exit from the EXEC

name-connection Name an existing network connection

pad Open a X.29 PAD connection

ping Send echo messages

resume Resume an active network connection

show Show running system information

systat Display information about terminal lines

telnet Open a telnet connection

terminal Set terminal line parameters

trace Trace route to destination

where List active connections

x3 Set X.3 parameters on PAD

Router(boot)>sh systat

^

% Invalid input detected at '^' marker.

Router(boot)>sh terminal

Line 1, Location: "", Type: ""

Length: 24 lines, Width: 80 columns

Baud rate (TX/RX) is 9600/9600, no parity, 2 stopbits, 8 databits

Status: Ready, Active

Capabilities: none

Modem state: Ready

Special Chars: Escape Hold Stop Start Disconnect Activation

^^x none - - none

Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch

0:10:00 never none not set

Session limit is not set.

Time since activation: 0:17:51

Editing is enabled.

History is enabled, history size is 10.

Full user help is disabled

Allowed transports are pad telnet mop. Preferred is telnet.

No output characters are padded

No special data dispatching characters

Modem hardware state: CTS* DSR* DTR RTS

Router(boot)>config t

^

% Invalid input detected at '^' marker.

Router(boot)>en

Password:

% Bad secrets

Router(boot)>en

Password:

% Bad secrets

Router(boot)>en

Password:

% Bad secrets

Router(boot)>en

Password:

% Bad secrets

Router(boot)>en

Password:

% Password timeout expired!

Password:

% Password timeout expired!

% Bad secrets

Router(boot)>o

Translating "O"...domain server (255.255.255.255)

% Unknown command or computer name, or unable to find computer address

Router(boot)>o/r0x2142

% Unknown command or computer name, or unable to find computer address

Router(boot)>i

Translating "I"...domain server (255.255.255.255)

% Unknown command or computer name, or unable to find computer address

Router(boot)>i

Translating "I"...domain server (255.255.255.255)

% Unknown command or computer name, or unable to find computer address

Router(boot)>ping 72.22.22.36

% IP protocol not running

Router(boot)>en

Password:

% Bad secrets

Router(boot)>write mem

^

% Invalid input detected at '^' marker.

Router(boot)>en

Password: €€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€

€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€

€€€€€€€€€€€€€€€€€€€€€€€€€€€ø€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€€

--------------------------------------------------------------------------------

Do You Yahoo!?

Yahoo! Sports - Sign up for Fantasy Baseball

scarothe · ‎03-04-2002

Greetings:

Looking at your output, it does not appear you have an IOS on the router. A router will go to "boot#" mode when it does not have an IOS in it. When you do a "show flash", does it indicate a file? You will probably have to load a new IOS from your TFTP server.

Steve Carothers/Cisco

amakinde · ‎03-04-2002

Thanks for your reply. See, i have a similar device and copied the ios to a tftp,hopping that, i can then from the device that's not working copy the ios,But ican't get no promt from the router,all i can see is all cccccccccccccccccccc.Please help !!!!!!

o.hassairi · ‎03-05-2002

to download the soft you can go to the rommon mode.

when the router just begin to boot preess ctrl+break (you should use a good terminal to work: hyperterminal /WIN98 or CRT)

the rommon mode is like the setup of computer there you can change config register or download the soft

amakinde · ‎03-05-2002

Thanks again. I tried that & all i get can is just CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC

would you know, if i can use te Aux port?