cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
3844
Views
10
Helpful
13
Replies

Introduction to Packet Tracer, Create a Simple Network

YatinVij
Level 1
Level 1

Hello, 

 

I have went through this exercise/lab various times, and I keep having the same problem, in which when I ping Cisco.com, I get a message saying "Ping request could not find host Cisco.. Please check the name and try again". I would appreciate if anyone could help.

1 Accepted Solution

Accepted Solutions

Hi @YatinVij 

 

Currently, the server is connected to the Eth6 interface of the cloud:

1.jpg

 

But your cloud connection points to the Fa9 interface:

1.jpg

 

To correct this you can change the cloud connection to the Fa9 interface:

1.jpg

After that change, connectivity is successful:

1.jpg

 

Regards

 

Remember to mark the correct answers or solve them, because that helps other users with similar doubts.

 

 

View solution in original post

13 Replies 13

omz
VIP Alumni
VIP Alumni

packet tracer is a simulation environment .. you don't have internet connectivity from the devices

 

https://www.packettracernetwork.com/features/real-network-connection.html

luis_cordova
VIP Alumni
VIP Alumni

Hi @YatinVij 

 

Compress your exercise (winzip) and attach it to check.

 

Regards

This is the network I built in the packet tracer

Hi @YatinVij 

 

Currently, the server is connected to the Eth6 interface of the cloud:

1.jpg

 

But your cloud connection points to the Fa9 interface:

1.jpg

 

To correct this you can change the cloud connection to the Fa9 interface:

1.jpg

After that change, connectivity is successful:

1.jpg

 

Regards

 

Remember to mark the correct answers or solve them, because that helps other users with similar doubts.

 

 

Thank  You so much, I have been stuck on this for 2 days. 

Hello,

I tried following the solution you proffered, but i FastEthernet9 wasn't even available to me as an option. So I made use of FastEthernet8, but still didnt get any results.

 

Hello,

I tried following the solution you proffered, but i FastEthernet9 wasn't even available to me as an option. So I made use of FastEthernet8, but still didnt get any results.
Assistance please.

Hi @Khadkay 

 

Compress your exercise (winzip) and attach it to check.

 

Regards

 

Hi @luis_cordova 

winzip attached. 

 

Regards

 

Hi @Khadkay 

 

I have checked your exercise and you must make two changes:

1-Go to the cloud > config > cable and remove the current connection

1.jpg

Replace the Ethernet6 interface with the FastEthernet8 interface and add that new connection

2.jpg

That connection should look like this:

3.jpg

 

Regards

Remember to mark the correct answers as solved, because that helps other users with similar doubts.

 

Hi @Khadkay 

 

The second change is made on the wifi router

2-Go to the GUI tab of the router and change the IP of the router (for example the IP 192.168.0.1/24), also assigns the server IP as DNS (208.67.220.220)

4.jpg

Save the changes

6.jpg

Now go to both PCs and renew the DHCP request (click static and click DHCP)

7.jpg

After these changes, connectivity is successful.

9.jpg

 

 

 

Regards

Remember to mark the correct answers as solved, because that helps other users with similar doubts.

Hi @luis_cordova 

This was extremely helpful! I can finally continue learning without having revist uncompleted work! Thank you.

image.png

 
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: