MLS-MOVE errors

senthil.natarajan · ‎01-23-2003

Here is the syslog message that appear on the screen

Cisco Systems Console

C Catalyst 5500 switch on 600B 8th floor

Username: t2003 Jan 13 10:26:58 %MLS-4-RESUMESC:Resume MLS after detecting too m

any moves

2003 Jan 13 10:26:58 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

zv

Password:

600B-5500-8> en

2003 Jan 13 10:27:04 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:27:04 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

Password:

600B-5500-8> (enable) 2003 Jan 13 10:27:09 %MLS-4-RESUMESC:Resume MLS after dete

cting too many moves

2003 Jan 13 10:27:09 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:27:14 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:27:14 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

sh tech

Unknown command "show tech". Use 'show help' for more info.

600B-5500-8> (enable) 2003 Jan 13 10:27:19 %MLS-4-RESUMESC:Resume MLS after dete

cting too many moves

2003 Jan 13 10:27:19 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:27:24 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:27:24 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:27:29 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:27:29 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

600B-5500-8> (enable) 2003 Jan 13 10:27:34 %MLS-4-RESUMESC:Resume MLS after dete

cting too many moves

2003 Jan 13 10:27:34 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

sh test2003 Jan 13 10:27:39 %MLS-4-RESUMESC:Resume MLS after detecting too many

moves

2003 Jan 13 10:27:39 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

Environmental Status (. = Pass, F = Fail, U = Unknown, N = Not Present)

PS (3.3V): N PS (12V): . PS (24V): . PS1: . PS2: .

PS1 Fan: . PS2 Fan : . Clock(A/B): A Chassis-Ser-EEPROM: .

Temperature: . Fan: .

Module 1 : 2-port 1000BaseX Supervisor IIIG

Network Management Processor (NMP) Status: (. = Pass, F = Fail, U = Unknown)

ROM: . Flash-EEPROM: . Ser-EEPROM: . NVRAM: . MCP Comm: .

EARL III Status :

DisableIndexLearnTest: .

DontLearnTest: .

DisableNewLearnTest: .

ConditionalLearnTest: .

MonitorColorFloodTest: .

EarlTrapTest: .

StaticMacAndTypeTest: .

BadDvlanTest: .

BadBpduTest: .

IndexMatchTest: .

ProtocolTypeTest: .

IgmpTest: .

SourceMissTest: .

--More--2003 Jan 13 10:27:44 %MLS-4-RESUMESC:Resume MLS after detecting too many

moves

2003 Jan 13 10:27:44 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

SourceModifiedTest: .

ArpaToArpaShortcutTest: .

ArpaToSnapShortcutTest: .

SnapToArpaShortcutTest: .

SnapToSnapShortcutTest: .

SoftwareShortcutTest: .

MulticastExpansionTest: .

DontShortcutTest: .

ShortcutTableFullTest: .

ArpaToArpaShortcutTest(IPX): .

ArpaToSnapShortcutTest(IPX): .

ArpaToSapShortcutTest(IPX): .

ArpaToRawShortcutTest(IPX): .

SnapToArpaShortcutTest(IPX): .

SnapToSnapShortcutTest(IPX): .

SnapToSapShortcutTest(IPX): .

SnapToRawShortcutTest(IPX): .

SapToArpaShortcutTest(IPX): .

SapToSnapShortcutTest(IPX): .

SapToSapShortcutTest(IPX): .

SapToRawShortcutTest(IPX): .

RawToArpaShortcutTest(IPX): .

RawToSnapShortcutTest(IPX): .

--More--2003 Jan 13 10:27:49 %MLS-4-RESUMESC:Resume MLS after detecting too many

moves

2003 Jan 13 10:27:49 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

RawToSapShortcutTest(IPX): .

RawToRawShortcutTest(IPX): .

SoftwareShortcutTest(IPX): .

DontShortcutTest(IPX): .

ShortcutTableFullTest(IPX): .

Line Card Diag Status for Module 1 (. = Pass, F = Fail, N = N/A)

CPU : . Sprom : . Bootcsum : . Archsum : N

RAM : . LTL : . CBL : . DPRAM : . ARBITER : N

Phoenix : . Pkt Bufs : . Repeater : N FLASH : N

Phoenix : . TrafficMeter: . UplinkSprom : . PhoenixSprom: .

PHOENIX Status :

Ports T1 R1 T2 R2

---------------------

. . . .

GIGMAC Status :

Ports 1 2

-----------

. .

PHOENIX Port Status :

Ports 9 17 18 19 20 21 22

INBAND A->B B->A B->C C->B A->C C->A

------------------------------------------

. . . . . . .

Packet Buffer Status :

Ports 1 2

-----------

. .

PHOENIX Packet Buffer Status :

Ports INBAND A<->B B<->C A<->C

------------------------------

. . . .

Loopback Status [Reported by Module 1] :

Ports 1 2 9

--------------

. . .

600B-5500-8> (enable) sh2003 Jan 13 10:27:54 %MLS-4-RESUMESC:Resume MLS after d

etecting too many moves

2003 Jan 13 10:27:54 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

tech

Unknown command "show tech". Use 'show help' for more info.

600B-5500-8> (enable) 2003 Jan 13 10:27:59 %MLS-4-RESUMESC:Resume MLS after dete

cting too many moves

2003 Jan 13 10:27:59 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:28:04 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:28:04 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

wr term

.....2003 Jan 13 10:28:09 %MLS-4-RESUMESC:Resume MLS after detecting too many mo

ves

2003 Jan 13 10:28:09 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

..............

..

begin

!

#version 5.1(1a)

!

set password $1$FMFQ$HfZR5DUszVHIRhrz4h6V70

2003 Jan 13 10:28:14 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:28:14 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:28:19 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:28:19 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:28:24 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:28:24 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

set enablepass $1$FMFQ$HfZR5DUszVHIRhrz4h6V70

set prompt 600B-5500-8>

set length 24 default

set logout 0

set banner motd ^CC Catalyst 5500 switch on 600B 8th floor^C

!

#system

set system baud 9600

set system modem disable

set system name 600B-5500-8

set system location 600B 8th Floor

set system contact

!

#snmp

set snmp community read-only d0ntw0rk

set snmp community read-write 14u24me

set snmp community read-write-all 14u24me

set snmp rmon enable

set snmp trap enable module

set snmp trap enable chassis

set snmp trap disable bridge

set snmp trap disable repeater

set snmp trap disable vtp

--More--2003 Jan 13 10:28:29 %MLS-4-RESUMESC:Resume MLS after detecting too many

moves

2003 Jan 13 10:28:29 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

set snmp trap disable auth

set snmp trap disable ippermit

set snmp trap disable vmps

set snmp trap disable entity

set snmp trap disable config

set snmp trap disable stpx

set snmp trap disable syslog

set snmp extendedrmon vlanmode disable

set snmp extendedrmon vlanagent disable

set snmp extendedrmon enable

set snmp trap 156.29.3.189 public

!

#tacacs+

set tacacs server 10.9.0.72 primary

set tacacs server 10.9.6.135

set tacacs attempts 3

set tacacs directedrequest disable

set tacacs key semperfi

set tacacs timeout 5

!

#radius

set radius deadtime 0

set radius timeout 5

--More--2003 Jan 13 10:28:35 %MLS-4-RESUMESC:Resume MLS after detecting too many

moves

2003 Jan 13 10:28:35 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:28:40 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:28:40 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:28:45 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:28:45 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:28:50 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:28:50 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:28:55 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

set 2003 Jan 13 10:28:55 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(

40000000)

radius retransmit 2

!

#authentication

set authentication login tacacs enable console primary

set authentication login tacacs enable telnet primary

set authentication enable tacacs enable console primary

set authentication enable tacacs enable telnet primary

set authentication login radius disable console

set authentication login radius disable telnet

set authentication enable radius disable console

set authentication enable radius disable telnet

set authentication login local enable console

set authentication login local enable telnet

set authentication enable local enable console

set authentication enable local enable telnet

!

#bridge

set bridge ipx snaptoether 8023raw

set bridge ipx 8022toether 8023

set bridge ipx 8023rawtofddi snap

!

#vtp

set vtp domain disable

--More--2003 Jan 13 10:29:00 %MLS-4-RESUMESC:Resume MLS after detecting too many

moves

2003 Jan 13 10:29:00 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:29:05 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:29:05 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

set vtp mode server

set vtp v2 disable

set vtp pruning disable

set vtp pruneeligible 2-1000

clear vtp pruneeligible 1001-1005

set vlan 1 name default type ethernet mtu 1500 said 100001 state active

set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active

set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state activ

e bridge 0x0 stp ieee

set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active br

idge 0x0 stp ibm

set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state acti

ve parent 0 ring 0x0 mode srb aremaxhop 7 stemaxhop 7

!

#ip

set interface sc0 1 10.105.0.20/255.255.0.0 10.105.255.255

set interface sc0 up

set interface sl0 0.0.0.0 0.0.0.0

set interface sl0 up

set arp agingtime 1200

set ip redirect enable

set ip unreachable enable

set ip fragmentation enable

set ip route 0.0.0.0/0.0.0.0 10.105.0.1

set ip alias default 0.0.0.0

--More--2003 Jan 13 10:29:10 %MLS-4-RESUMESC:Resume MLS after detecting too many

moves

2003 Jan 13 10:29:10 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

!

#Command alias

!

#vmps

set vmps server retry 3

set vmps server reconfirminterval 60

set vmps tftpserver 0.0.0.0 vmps-config-database.1

set vmps state disable

!

#dns

set ip dns disable

!

#spantree

#uplinkfast groups

set spantree uplinkfast disable

#backbonefast

set spantree backbonefast disable

set spantree enable all

#vlan 1

set spantree fwddelay 15 1

set spantree hello 2 1

set spantree maxage 20 1

--More--2003 Jan 13 10:29:15 %MLS-4-RESUMESC:Resume MLS after detecting too many

moves

2003 Jan 13 10:29:15 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:29:20 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:29:20 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

set spantree priority 8192 1

#vlan 1003

set spantree fwddelay 15 1003

set spantree hello 2 1003

set spantree maxage 20 1003

set spantree priority 32768 1003

set spantree portstate 1003 block 0

set spantree portcost 1003 62

set spantree portpri 1003 4

set spantree portfast 1003 disable

#vlan 1005

set spantree fwddelay 15 1005

set spantree hello 2 1005

set spantree maxage 20 1005

set spantree priority 32768 1005

set spantree multicast-address 1005 ieee

!

#cgmp

set cgmp disable

set cgmp leave disable

!

#syslog

set logging console enable

--More--2003 Jan 13 10:29:25 %MLS-4-RESUMESC:Resume MLS after detecting too many

moves

2003 Jan 13 10:29:25 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

set logging server enable

set logging server 156.29.2.35

set logging server 10.9.0.235

set logging level cdp 2 default

set logging level mcast 2 default

set logging level dtp 5 default

set logging level dvlan 2 default

set logging level earl 2 default

set logging level fddi 2 default

set logging level ip 2 default

set logging level pruning 2 default

set logging level snmp 2 default

set logging level spantree 2 default

set logging level sys 6 default

set logging level tac 2 default

set logging level tcp 2 default

set logging level telnet 2 default

set logging level tftp 2 default

set logging level vtp 2 default

set logging level vmps 2 default

set logging level kernel 2 default

set logging level filesys 2 default

set logging level drip 2 default

--More--2003 Jan 13 10:29:30 %MLS-4-RESUMESC:Resume MLS after detecting too many

moves

2003 Jan 13 10:29:30 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

set logging level pagp 2 default

set logging level mgmt 5 default

set logging level mls 5 default

set logging level protfilt 2 default

set logging level security 2 default

set logging level radius 2 default

set logging level udld 2 default

set logging level gvrp 2 default

set logging server facility LOCAL7

!

#ntp

set ntp broadcastclient disable

set ntp broadcastdelay 3000

set ntp client disable

set ntp authentication disable

clear timezone

set summertime disable

!

#permit list

set ip permit disable

!

#drip

set tokenring reduction enable

--More--2003 Jan 13 10:29:35 %MLS-4-RESUMESC:Resume MLS after detecting too many

moves

2003 Jan 13 10:29:35 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

set tokenring distrib-crf disable

!

#igmp

set igmp disable

!

#protocolfilter

set protocolfilter disable

!

#mls

set mls enable

set mls disable ipx

set mls flow destination

set mls agingtime 256

set mls agingtime ipx 256

set mls agingtime fast 0 0

set mls nde disable

!

#standby ports

set standbyports enable

!

#vlan mapping

!

#gmrp

--More--2003 Jan 13 10:29:40 %MLS-4-RESUMESC:Resume MLS after detecting too many

moves

2003 Jan 13 10:29:40 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:29:45 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:29:45 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:29:50 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:29:50 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:29:55 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:29:55 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:30:00 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:30:00 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

set gmrp disable

!

#garp

set garp timer join 200

set garp timer leave 600

set garp timer leaveall 10000

!

#CDP

set cdp interval 60

set cdp holdtime 180

set cdp enable

!

#qos

set qos disable

set qos map 1q4t 1 1 cos 0

set qos map 1q4t 1 1 cos 1

set qos map 1q4t 1 2 cos 2

set qos map 1q4t 1 2 cos 3

set qos map 1q4t 1 3 cos 4

set qos map 1q4t 1 3 cos 5

set qos map 1q4t 1 4 cos 6

set qos map 1q4t 1 4 cos 7

set qos wred-threshold 1q4t tx queue 1 10 20 40 100

!

#mls multicast

set mls multicast disable

!

#UDLD

set udld disable

!

#module 1 : 2-port 1000BaseX Supervisor IIIG

set module name 1

set vlan 1 1/1-2

set port enable 1/2

set port disable 1/1

set port level 1/1-2 normal

set port trap 1/1-2 disable

set port name 1/2 to 1/2 5th fl 5500

set port name 1/1

set port broadcast 1/1-2 100%

set port protocol 1/1-2 ip on

set port protocol 1/1-2 ipx auto

set port protocol 1/1-2 group auto

set port negotiation 1/1-2 enable

set port flowcontrol 1/1-2 send off

--More--2003 Jan 13 10:30:05 %MLS-4-RESUMESC:Resume MLS after detecting too many

moves

2003 Jan 13 10:30:05 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

set port flowcontrol 1/1-2 receive off

set cdp enable 1/1-2

set udld disable 1/1-2

set trunk 1/1 auto negotiate 1-1005

set trunk 1/2 auto negotiate 1-1005

set spantree portfast 1/1-2 disable

set spantree portcost 1/1-2 4

set spantree portpri 1/1-2 32

set spantree portvlanpri 1/1 0

set spantree portvlanpri 1/2 0

set spantree portvlancost 1/1 cost 3

set spantree portvlancost 1/2 cost 3

set port gvrp 1/1-2 disable

set gvrp registration normal 1/1-2

set gvrp applicant normal 1/1-2

set port gmrp 1/1-2 enable

set gmrp registration normal 1/1-2

set gmrp fwdall disable 1/1-2

!

#module 2 : 2-port 1000BaseX Supervisor IIIG

set module name 2

set vlan 1 2/1-2

set port enable 2/2

set port disable 2/1

set port level 2/1-2 normal

set port trap 2/1-2 disable

set port name 2/2 to 2/2 5th fl 5500

set port name 2/1

set port broadcast 2/1-2 100%

set port protocol 2/1-2 ip on

set port protocol 2/1-2 ipx auto

set port protocol 2/1-2 group auto

set port negotiation 2/1-2 enable

set port flowcontrol 2/1-2 send off

set port flowcontrol 2/1-2 receive off

set cdp enable 2/1-2

set udld enable 2/1-2

set trunk 2/1 auto negotiate 1-1005

set trunk 2/2 auto negotiate 1-1005

set spantree portfast 2/1-2 disable

set spantree portcost 2/1-2 4

set spantree portpri 2/1-2 32

set spantree portvlanpri 2/1 0

set spantree portvlanpri 2/2 0

set spantree portvlancost 2/1 cost 3

set spantree portvlancost 2/2 cost 3

set port gvrp 2/1-2 disable

set gvrp registration normal 2/1-2

set gvrp applicant normal 2/1-2

set port gmrp 2/1-2 enable

set gmrp registration normal 2/1-2

set gmrp fwdall disable 2/1-2

!

#module 3 empty

!

#module 4 : 12-port 100BaseFX MM Ethernet

set module name 4

set module enable 4

set vlan 1 4/1-12

set port channel 4/1-4 off

set port channel 4/5-8 off

set port channel 4/9-12 off

set port channel 4/5-6 on

set port channel 4/1-4 auto

set port channel 4/7-8 auto

set port channel 4/9-12 auto

set port enable 4/1-12

set port level 4/1-12 normal

set port duplex 4/1-12 full

set port trap 4/1-12 disable

set port name 4/1 22nd Flr 2950 DSD

set port name 4/2 600b_13.1_2950

set port name 4/5 to 1/1 9th fl 5K

set port name 4/6 to 1/2 9th fl 5K

set port name 4/3-4,4/7-12

set port securi2003 Jan 13 10:30:11 %MLS-4-RESUMESC:Resume MLS after detecting t

oo many moves

ty 4/1-12 disable

s2003 Jan 13 10:30:11 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(400

00000)

et port broadcast 4/1-12 100%

set port membership 4/1-12 static

set port protocol 4/1-12 ip on

set port protocol 4/1-12 ipx auto

set port protocol 4/1-12 group auto

set port negotiation 4/1-12 enable

set port flowcontrol 4/1-12 send off

set port flowcontrol 4/1-12 receive on

set cdp enable 4/1-12

set udld disable 4/1-12

set trunk 4/1 off negotiate 1-1005

set trunk 4/2 off negotiate 1-1005

set trunk 4/3 off negotiate 1-1005

set trunk 4/4 off negotiate 1-1005

set trunk 4/5 off negotiate 1-1005

set trunk 4/6 off negotiate 1-1005

set trunk 4/7 off negotiate 1-1005

set trunk 4/8 off negotiate 1-1005

set trunk 4/9 off negotiate 1-1005

set trunk 4/10 off negotiate 1-1005

set trunk 4/11 off negotiate 1-1005

set trunk 4/12 off negotiate 1-1005

set spantree portfast 4/1-12 disable

set spantree portcost 4/1-12 19

set spantree portpri 4/1-12 32

set spantree portvlanpri 4/1 0

set spantree portvlanpri 4/2 0

set spantree portvlanpri 4/3 0

set spantree portvlanpri 4/4 0

set spantree portvlanpri 4/5 0

set spantree portvlanpri 4/6 0

set spantree portvlanpri 4/7 0

set spantree portvlanpri 4/8 0

set spantree portvlanpri 4/9 0

set spantree portvlanpri 4/10 0

set spantree portvlanpri 4/11 0

set spantree portvlanpri 4/12 0

set spantree portvlancost 4/1 cost 18

set spantree portvlancost 4/2 cost 18

set spantree portvlancost 4/3 cost 18

set spantree portvlancost 4/4 cost 18

set spantree portvlancost 4/5 cost 18

set spantree portvlancost 4/6 cost 18

set spantree portvlancost 4/7 cost 18

set spantree portvlancost 4/8 cost 18

set spantree portvlancost 4/9 cost 18

set spantree portvlancost 4/10 cost 18

set spantree portvlancost 4/11 cost 18

set spantree portvlancost 4/12 cost 18

set port gvrp 4/1-12 disable

set gvrp registration normal 4/1-12

set gvrp applicant normal 4/1-12

set port gmrp 4/1-12 enable

set gmrp registration normal 4/1-12

set gmrp fwdall disable 4/1-12

!

#module 5 : 12-port 100BaseFX MM Ethernet

set module name 5

set module enable 5

set vlan 1 5/1-12

set port channel 5/1-4 off

set port channel 5/5-8 off

set port channel 5/9-12 off

set port channel 5/5-6 on

set port channel 5/7-8 on

set port channel 5/9-10 on

set port enable 5/1-12

set port level 5/1-12 normal

set port duplex 5/1-12 full

set port trap 5/1-12 disable

set port name 5/1 to 1/1 7th fl 5000

set port name 5/2 to 1/2 7th fl 5000

set port name 5/5 to 1/1 10th fl 5K

set port name 5/6 to 1/2 10th fl 5K

set port name 5/7 to 1/1 11th fl 5K

set port name 5/8 to 1/2 11th fl 5K

set port name 5/9 to 1/1 13th fl 5K

set port name 5/10 to 1/2 13th fl 5K

set port name 5/11 to 1/2 4th fl 5k

set port name 5/12 to 1/2 4th fl 5k

set port name 5/3-4

set port security 5/1-12 disable

set port broadcast 5/1-12 0

set port membership 5/1-12 static

set port protocol 5/1-12 ip on

set port protocol 5/1-12 ipx auto

set port protocol 5/1-12 group auto

set cdp enable 5/1-12

set udld disable 5/1-12

set trunk 5/1 off isl 1-1005

set trunk 5/2 off isl 1-1005

set trunk 5/3 off isl 1-1005

set trunk 5/4 off isl 1-1005

set trunk 5/5 off isl 1-1005

set trunk 5/6 off isl 1-1005

set trunk 5/7 off isl 1-1005

set trunk 5/8 off isl 1-1005

set trunk 5/9 off isl 1-1005

set trunk 5/10 off isl 1-1005

set trunk 5/11 off isl 1-1005

set trunk 5/12 off isl 1-1005

set spantree portfast 5/1-12 disable

set spantree portcost 5/1-12 10

set spantree portpri 5/1-12 32

set spantree portvlanpri 5/1 0

set spantree portvlanpri 5/2 0

set spantree portvlanpri 5/3 0

set spantree portvlanpri 5/4 0

set spantree portvlanpri 5/5 0

set spantree portvlanpri 5/6 0

set spantree portvlanpri 5/7 0

set spantree portvlanpri 5/8 0

set spantree portvlanpri 5/9 0

set spantree portvlanpri 5/10 0

set spantree portvlanpri 5/11 0

set spantree portvlanpri 5/12 0

set spantree portvlancost 5/1 cost 18

set spantree portvlancost 5/2 cost 18

set spantree portvlancost 5/3 cost 18

set spantree portvlancost 5/4 cost 18

set spantree portvlancost 5/5 cost 18

set spantree portvlancost 5/6 cost 18

set spantree portvlancost 5/7 cost 18

set spantree portvlancost 5/8 cost 18

set spantree portvlancost 5/9 cost 18

set spantree portvlancost 5/10 cost 18

set spantree portvlancost 5/11 cost 18

set spantree portvlancost 5/12 cost 18

set port gmrp 5/1-12 enable

set gmrp registration normal 5/1-12

--More--2003 Jan 13 10:30:16 %MLS-4-RESUMESC:Resume MLS after detecting too many

moves

2003 Jan 13 10:30:16 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

set gmrp fwdall disable 5/1-12

!

#module 6 : 12-port 100BaseFX MM Ethernet

set module name 6

set module enable 6

set vlan 1 6/1-12

set port channel 6/1-4 off

set port channel 6/5-8 off

set port channel 6/9-12 off

set port channel 6/1-4 on

set port channel 6/5-8 auto

set port enable 6/1-12

set port level 6/1-12 normal

set port duplex 6/1-12 full

set port trap 6/1-12 disable

set port name 6/1 to 5/1-4 12th 5500

set port name 6/2 to 5/1-4 12th 5500

set port name 6/3 to 5/1-4 12th 5500

set port name 6/4 to 5/1-4 12th 5500

set port name 6/5 DEFECTIVE

set port name 6/6 hold for 13th fl

set port name 6/7 to 1/1 6th 5500A

set port name 6/8 to 1/2 6th 5500A

set port name 6/9-12

set port security 6/1-12 disable

set port broadcast 6/1-12 0

set port membership 6/1-12 static

set port protocol 6/1-12 ip on

set port protocol 6/1-12 ipx auto

set port protocol 6/1-12 group auto

set cdp enable 6/1-12

set udld disable 6/1-12

set trunk 6/1 off isl 1-1005

set trunk 6/2 off isl 1-1005

set trunk 6/3 off isl 1-1005

set trunk 6/4 off isl 1-1005

set trunk 6/5 off isl 1-1005

set trunk 6/6 off isl 1-1005

set trunk 6/7 off isl 1-1005

set trunk 6/8 off isl 1-1005

set trunk 6/9 off isl 1-1005

set trunk 6/10 off isl 1-1005

set trunk 6/11 off isl 1-1005

set trunk 6/12 off isl 1-1005

set spantree portfast 6/1-12 disable

set spantree portcost 6/1-12 10

set spantree portpri 6/1-12 32

set spantree portvlanpri 6/1 0

set spantree portvlanpri 6/2 0

set spantree portvlanpri 6/3 0

set spantree portvlanpri 6/4 0

set spantree portvlanpri 6/5 0

set spantree portvlanpri 6/6 0

set spantree portvlanpri 6/7 0

set spantree portvlanpri 6/8 0

set spantree portvlanpri 6/9 0

set spantree portvlanpri 6/10 0

set spantree portvlanpri 6/11 0

set spantree portvlanpri 6/12 0

set spantree portvlancost 6/1 cost 18

set spantree portvlancost 6/2 cost 18

set spantree portvlancost 6/3 cost 18

set spantree portvlancost 6/4 cost 18

set spantree portvlancost 6/5 cost 18

set spantree portvlancost 6/6 cost 18

set spantree portvlancost 6/7 cost 18

set spantree portvlancost 6/8 cost 18

set spantree portvlancost 6/9 cost 18

set spantree portvlancost 6/10 cost 18

set spantree portvlancost 6/11 cost 18

set spantree portvlancost 6/12 cost 18

set port gmrp 6/1-12 enable

set gmrp registration normal 6/1-12

set gmrp fwdall disable 6/1-12

!

#module 7 : 24-port 10/100BaseTX Ethernet

set module name 7

set module enable 7

set vlan 1 7/1-24

set port channel 7/1-4 off

set port channel 7/5-8 off

set port channel 7/9-12 off

set port channel 7/13-16 off

set port channel 7/17-20 off

set port channel 7/21-24 off

set port channel 7/1-4 auto

set port channel 7/5-8 auto

set port channel 7/9-12 auto

set port channel 7/13-16 auto

set port channel 7/17-20 auto

set port channel 7/21-24 auto

set port enable 7/1-5,7/10-24

set port disable 7/6-9

set port level 7/1-24 normal

set port speed 7/18 auto

set port speed 7/1-17,7/19-24 100

set port duplex 7/1-17,7/19-24 full

set port trap 7/1-24 disable

set port name 7/1 H2OBERRY

set port name 7/2 H2OBERRY

set port name 7/3 H2OBERRY

set port name 7/4 H2OBERRY

set port name 7/5 H2OBERRY RIB

set port name 7/12 081-312

set port name 7/13 081-257

set port name 7/14 081-258

set port name 7/15 081-259

set port name 7/16 081-269

set port name 7/17 081-297

set port name 7/18 081-298

set port name 7/19 081-299

set port name 7/20 081-300

set port name 7/21 h2o-blue

set port name 7/22 h2o-blue

set port name 7/23 h2o-blue

set port name 7/24 h2o-blue

set port name 7/6-11

set port security 7/1-24 disable

set port broadcast 7/1-24 100%

set port membership 7/1-24 static

set port protocol 7/1-24 ip on

set port protocol 7/1-24 ipx auto

set port protocol 7/1-24 group auto

set port negotiation 7/1-24 enable

set port flowcontrol 7/1-24 send off

set port flowcontrol 7/1-24 receive on

set cdp enable 7/1-24

set trunk 7/1 off negotiate 1-1005

set trunk 7/2 off negotiate 1-1005

set trunk 7/3 off negotiate 1-1005

set trunk 7/4 off negotiate 1-1005

set trunk 7/5 off negotiate 1-1005

set trunk 7/6 off negotiate 1-1005

set trunk 7/7 off negotiate 1-1005

set trunk 7/8 o2003 Jan 13 10:30:21 %MLS-4-RESUMESC:Resume MLS after detecting

too many moves

ff negotiate 1-1005

se2003 Jan 13 10:30:21 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(40

000000)

t trunk 7/9 off negotiate 1-1005

set trunk 7/10 off negotiate 1-1005

set trunk 7/11 off negotiate 1-1005

set trunk 7/12 off negotiate 1-1005

set trunk 7/13 off negotiate 1-1005

set trunk 7/14 off negotiate 1-1005

set trunk 7/15 off negotiate 1-1005

set trunk 7/16 off negotiate 1-1005

set trunk 7/17 off negotiate 1-1005

set trunk 7/18 off negotiate 1-1005

set trunk 7/19 off negotiate 1-1005

set trunk 7/20 off negotiate 1-1005

set trunk 7/21 off negotiate 1-1005

set trunk 7/22 off negotiate 1-1005

set trunk 7/23 off negotiate 1-1005

set trunk 7/24 off negotiate 1-1005

set spantree portfast 7/6-24 enable

set spantree portfast 7/1-5 disable

set spantree portcost 7/1-24 19

set spantree portpri 7/1-24 32

set spantree portvlanpri 7/1 0

set spantree portvlanpri 7/2 0

set spantree portvlanpri 7/3 0

set spantree portvlanpri 7/4 0

set spantree portvlanpri 7/5 0

set spantree portvlanpri 7/6 0

set spantree portvlanpri 7/7 0

set spantree portvlanpri 7/8 0

set spantree portvlanpri 7/9 0

set spantree portvlanpri 7/10 0

set spantree portvlanpri 7/11 0

set spantree portvlanpri 7/12 0

set spantree portvlanpri 7/13 0

set spantree portvlanpri 7/14 0

set spantree portvlanpri 7/15 0

set spantree portvlanpri 7/16 0

set spantree portvlanpri 7/17 0

set spantree portvlanpri 7/18 0

set spantree portvlanpri 7/19 0

set spantree portvlanpri 7/20 0

set spantree portvlanpri 7/21 0

set spantree portvlanpri 7/22 0

set spantree portvlanpri 7/23 0

set spantree portvlanpri 7/24 0

set spantree portvlancost 7/1 cost 18

set spantree portvlancost 7/2 cost 18

set spantree portvlancost 7/3 cost 18

set spantree portvlancost 7/4 cost 18

set spantree portvlancost 7/5 cost 18

set spantree portvlancost 7/6 cost 18

set spantree portvlancost 7/7 cost 18

set spantree portvlancost 7/8 cost 18

set spantree portvlancost 7/9 cost 18

set spantree portvlancost 7/10 cost 18

set spantree portvlancost 7/11 cost 18

set spantree portvlancost 7/12 cost 18

set spantree portvlancost 7/13 cost 18

set spantree portvlancost 7/14 cost 18

set spantree portvlancost 7/15 cost 18

set spantree portvlancost 7/16 cost 18

set spantree portvlancost 7/17 cost 18

set spantree portvlancost 7/18 cost 18

set spantree portvlancost 7/19 cost 18

set spantree portvlancost 7/20 cost 18

set spantree portvlancost 7/21 cost 18

set spantree portvlancost 7/22 cost 18

set spantree portvlancost 7/23 cost 18

set spantree portvlancost 7/24 cost 18

set port gvrp 7/1-24 disable

set gvrp registration normal 7/1-24

set gvrp applicant normal 7/1-24

set port gmrp 7/1-24 enable

set gmrp registration normal 7/1-24

set gmrp fwdall disable 7/1-24

!

#module 8 empty

!

#module 9 : 24-port 10/100BaseTX Ethernet

set module name 9

set module enable 9

set vlan 1 9/1-24

set port enable 9/1-24

set port level 9/1-24 normal

set port speed 9/2-10 10

set port speed 9/1,9/11-24 100

set port duplex 9/1,9/11-24 full

set port duplex 9/2-10 half

set port trap 9/1-24 disable

set port name 9/1 Link to 7505

set port name 9/2 600B_01 EMME

set port name 9/3 600B_01 Slot 2

set port name 9/4 600B_01 Slot 3

set port name 9/5 600B_01 Slot 4

set port name 9/6 600B_01 Slot 5

set port name 9/7 600B_01 Slot 6

set port name 9/8 600B_01 Slot 7

set port name 9/9 600B_01 Slot 8

set port name 9/10 Water370

set port name 9/11 Blue cable sys4559

set port name 9/12 Blue Cable sys4557

set port name 9/13 081-251

set port name 9/14 081-221

set port name 9/15 081-239

set port name 9/16 081-245

set port name 9/17 081-246

set port name 9/18 081-252

set port name 9/19 081-253

set port name 9/20 081-255

set port name 9/21 081-256

set port name 9/22 081-263

set port name 9/23 081-264

set port name 9/24 081-213

set port security 9/1-24 disable

set port broadcast 9/1-24 0

set port membership 9/1-24 static

set port protocol 9/1-24 ip on

set port protocol 9/1-24 ipx auto

set port protocol 9/1-24 group auto

set cdp enable 9/1-24

set spantree portfast 9/2-24 enable

set spantree portfast 9/1 disable

set spantree portcost 9/1-24 10

set spantree portpri 9/1-24 32

set port gmrp 9/1-24 enable

set gmrp registration normal 9/1-24

set gmrp fwdall disable 9/1-24

!

#module 10 : 24-port 10/100BaseTX Ethernet

set module name 10

set module enable 10

set vlan 1 10/1-24

set port enable 10/1-24

set port level 10/1-24 normal

set port speed 10/23 auto

set port speed 10/3,10/12 10

set port speed 10/1-2,10/4-11,10/13-22,10/24 100

set port duplex 10/1-2,10/4-11,10/13-22,10/24 full

set port duplex 10/3,10/12 half

set port trap 10/1-24 disable

set port name 10/1 081-230

--More--2003 Jan 13 10:30:26 %MLS-4-RESUMESC:Resume MLS after detecting too many

moves

set port name 12003 Jan 13 10:30:26 %MLS-4-MOVEOVERFLOW:Too many moves, st

op MLS for 5 sec(40000000)

0/2 081-227

set port name 10/3 081-210

set port name 10/4 081-229

set port name 10/5 081-259

set port name 10/6 081-260

set port name 10/7 081-226

set port name 10/8 081-231

set port name 10/9 081-228

set port name 10/10 081-236

set port name 10/11 081-248

set port name 10/12 081-225

set port name 10/13 081-249

set port name 10/14 081-211

set port name 10/15 081-212

set port name 10/16 081-202

set port name 10/17 081-208

set port name 10/18 081-215

set port name 10/19 081-219

set port name 10/20 081-220

set port name 10/21 081-247

set port name 10/22 081-203

set port name 10/23 081-229

set port name 10/24 081-233

set port security 10/1-24 disable

set port broadcast 10/1-24 0

set port membership 10/1-24 static

set port protocol 10/1-24 ip on

set port protocol 10/1-24 ipx auto

set port protocol 10/1-24 group auto

set cdp enable 10/1-24

set spantree portfast 10/1-24 enable

set spantree portcost 10/1-24 10

set spantree portpri 10/1-24 32

set port gmrp 10/1-24 enable

set gmrp registration normal 10/1-24

set gmrp fwdall disable 10/1-24

!

#module 11 : 24-port 10/100BaseTX Ethernet

set module name 11

set module enable 11

set vlan 1 11/1-24

set port enable 11/1-24

set port level 11/1-24 normal

set port speed 11/3 auto

set port speed 11/20 10

set port speed 11/1-2,11/4-19,11/21-24 100

set port duplex 11/1-2,11/4-19,11/21-24 full

set port duplex 11/20 half

set port trap 11/1-24 disable

set port name 11/1 081-240

set port name 11/2 081-241

set port name 11/3 081-242

set port name 11/4 081-222

set port name 11/5 081-271

set port name 11/6 081-234

set port name 11/7 081-272

set port name 11/8 081-270

set port name 11/9 081-266

set port name 11/10 081-268

set port name 11/11 081-267

set port name 11/12 081-265

set port name 11/15 081-287

set port name 11/16 081-292

set port name 11/17 081-293

set port name 11/18 081-254

set port name 11/20 APC Env monitor

set port name 11/22 081-288

set port name 11/23 081-205a

set port name 11/24 081-206a

set port name 11/13-14,11/19,11/21

set port security 11/1-24 disable

set port broadcast 11/1-24 0

set port membership 11/1-24 static

set port protocol 11/1-24 ip on

set port protocol 11/1-24 ipx auto

set port protocol 11/1-24 group auto

set cdp enable 11/1-24

set spantree portfast 11/1-24 enable

set spantree portcost 11/1-24 10

set spantree portpri 11/1-24 32

set port gmrp 11/1-24 enable

set gmrp registration normal 11/1-24

set gmrp fwdall disable 11/1-24

!

#module 12 : 24-port 10/100BaseTX Ethernet

set module name 12

set module enable 12

set vlan 1 12/1-24

set port enable 12/1-24

set port level 12/1-24 normal

set port speed 12/4,12/21 10

set port speed 12/1-3,12/5-20,12/22-24 100

set port duplex 12/1-3,12/5-16,12/20,12/22,12/24 full

set port duplex 12/4,12/17-19,12/21,12/23 half

set port trap 12/1-24 disable

set port name 12/1 insight1

set port name 12/2 081-303

set port name 12/3 insight3

set port name 12/4 081-243

set port name 12/5 081-234

set port name 12/6 Cable tagged#10

set port name 12/7 081-237

set port name 12/8 081-216

set port name 12/9 081-306

set port name 12/10 081-282

set port name 12/11 081-235

set port name 12/12 081-224

set port name 12/13 081-204

set port name 12/14 081-250

set port name 12/15 081-286

set port name 12/16 081-301

set port name 12/17 sniffer#1-monitor

set port name 12/18 sniffer#3 trans

set port name 12/19 Sniffer#2-Trans

set port name 12/20 081-232

set port name 12/21 081-244 PrntWU_30

set port name 12/22 TR Router

set port name 12/23 Sniffer Tran

set port name 12/24 081-309

set port security 12/1-24 disable

set port broadcast 12/1-24 0

set port membership 12/1-24 static

set port protocol 12/1-24 ip on

set port protocol 12/1-24 ipx auto

set port protocol 12/1-24 group auto

set cdp enable 12/1-24

set spantree portfast 12/1-22,12/24 enable

set spantree portfast 12/23 disable

set spantree portcost 12/1-3,12/5-20,12/22-24 19

set spantree portcost 12/4,12/21 100

set spantree portpri 12/1-24 32

set port gmrp 12/1-24 enable

set gmrp registration normal 12/1-24

set gmrp fwdall disable 12/1-24

!

#module 13 empty

!

#module 15 empty

!

#module 16 empty

!

#switch port analyzer

!

#cam

set cam agingtime 1,1003,1005 300

!

#qos mac-cos

!

#gvrp

set gvrp dynamic-vlan-creation disable

set gvrp disable

end

600B-5500-8> (enable) 2003 Jan 13 10:30:31 %MLS-4-RESUMESC:Resume MLS after dete

cting too many moves

2003 Jan 13 10:30:31 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:30:36 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:30:36 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

600B-5500-8> (enable) sh lo2003 Jan 13 10:30:41 %MLS-4-RESUMESC:Resume MLS after

detecting too many moves

2003 Jan 13 10:30:41 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

g

Network Management Processor (ACTIVE NMP) Log:

Reset count: 3

Re-boot History: Dec 14 2002 12:34:39 3, Dec 14 2002 09:10:48 3

Bootrom Checksum Failures: 0 UART Failures: 0

Flash Checksum Failures: 0 Flash Program Failures: 0

Power Supply 1 Failures: 0 Power Supply 2 Failures: 3

Swapped to CLKA: 0 Swapped to CLKB: 0

Swapped to Processor 1: 1 Swapped to Processor 2: 0

DRAM Failures: 0

Exceptions: 0

Heap Memory Log:

Corrupted Block = none

NVRAM log:

01. 12/14/2002,12:43:54: updateRuntimeWithNVRAM:Redundancy switch over: 1

2003 Jan 13 10:30:46 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:30:46 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

Network Management Processor (STANDBY NMP) Log:

Reset count: 4

Re-boot History: Dec 14 2002 12:44:04 3, Dec 14 2002 09:15:20 3

Dec 14 2002 09:11:31 3

Bootrom Checksum Failures: 0 UART Failures: 0

Flash Checksum Failures: 0 Flash Program Failures: 0

Power Supply 1 Failures: 0 Power Supply 2 Failures: 3

Swapped to CLKA: 0 Swapped to CLKB: 0

Swapped to Processor 1: 0 Swapped to Processor 2: 1

DRAM Failures: 0

Exceptions: 0

Heap Memory Log:

Corrupted Block = none

NVRAM log:

01. 12/14/2002,09:12:00: check_block_and_log:Block 0 checksum failed: 0x689B(0x6

89A)

02. 12/14/2002,09:15:37: convert_post_SAC_CiscoMIB:Nvram block 0 unconvertable:

14(8)

03. 12/14/2002,09:15:37: check_block_and_log:Block 35 has been deallocated: (0x5

0003318)

04. 12/14/2002,09:15:37: check_block_and_log:Block 44 has been deallocated: (0x5

0019630)

05. 12/14/2002,09:15:37: convert_post_SAC_CiscoMIB:Nvram block 62 unconvertable:

4(2)

06. 12/14/2002,12:34:29: updateRuntimeWithNVRAM:Redundancy switch over: 2

Module 4 Log:

2003 Jan 13 10:30:51 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

Reset Count: 3

R2003 Jan 13 10:30:51 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4

0000000)

eset History: Sat Dec 14 2002, 12:43:59

Sat Dec 14 2002, 12:34:33

Sat Dec 14 2002, 09:13:15

Module 5 Log:

Reset Count: 4

Reset History: Sat Dec 14 2002, 12:43:59

Sat Dec 14 2002, 12:34:33

Sat Dec 14 2002, 10:59:02

Sat Dec 14 2002, 09:13:12

Module 6 Log:

Reset Count: 3

Reset History: Sat Dec 14 2002, 12:43:59

Sat Dec 14 2002, 12:34:33

Sat Dec 14 2002, 09:13:13

Module 7 Log:

Reset Count: 3

Reset History: Sat Dec 14 2002, 12:43:58

Sat Dec 14 2002, 12:34:33

Sat Dec 14 2002, 09:13:15

Module 9 Log:

Reset Count: 3

Reset History: Sat Dec 14 2002, 12:43:59

Sat Dec 14 2002, 12:34:33

Sat Dec 14 2002, 09:13:13

Module 10 Log:

Reset Count: 3

Reset History: Sat Dec 14 2002, 12:43:59

Sat Dec 14 2002, 12:34:34

Sat Dec 14 2002, 09:13:13

Module 11 Log:

Reset Count: 3

Reset History: Sat Dec 14 2002, 12:43:59

Sat Dec 14 2002, 12:34:33

Sat Dec 14 2002, 09:13:13

Module 12 Log:

Reset Count: 3

Reset History: Sat Dec 14 2002, 12:43:59

Sat Dec 14 2002, 12:34:33

Sat Dec 14 2002, 09:13:13

600B-5500-8> (enable) 2003 Jan 13 10:30:56 %MLS-4-RESUMESC:Resume MLS after dete

cting too many moves

2003 Jan 13 10:30:56 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

2003 Jan 13 10:31:01 %MLS-4-RESUMESC:Resume MLS after detecting too many moves

2003 Jan 13 10:31:01 %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(4000

0000)

I found a cisco document which says

----------------

%MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec

Problem: Sporadic or constant "%MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec" syslog messages are generated on the switch.

Platform: Catalyst 5000 family switches

The following is an example of the syslog output you will see when this error occurs:

%MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(20000000)

%MLS-4-RESUMESC:Resume MLS after detecting too many moves

%MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(20000000)

%MLS-4-RESUMESC:Resume MLS after detecting too many moves

These syslog messages indicate that the switch is relearning one or more MAC addresses on multiple ports in rapid succession. For example, on an access switch with two uplinks to the core of the network, the switch might learn a given MAC address first on one uplink and then on the other very rapidly.

If you see these messages infrequently, it is most likely a transitory Layer 2 (spanning-tree) loop, resulting in packet flooding in one or more VLANs.

If you are seeing an excessive number of these messages (for example, if your syslog server log file or your switch console are being flooded with these messages), the problem might be due to:

1.A permanent Layer 2 (spanning-tree) loop

2.One or more faulty switch ports

3.A bad cable (for example, a unidirectional fiber link)

4.Other bad hardware (not necessarily on the switch generating the messages)

5.Misconfigured device (for example, a traffic generator sending traffic to two switch ports using the same MAC address)

If you are confident there is no Layer 2 loop or faulty hardware, you are not using MLS on the switch, and you want to eliminate these messages, you can disable MLS on the switch (with the set mls disable command). Alternately, you can modify the logging level for the "MLS" facility to 3 or lower using the command set logging level mls 3 default. However, these solutions simply mask the problem.

In addition to the suggestions above, consider upgrading the switch software to the latest maintenance release for your software release train, which integrates several optimizations relating to this problem.

---------------------

We are still trying to detect a spanning tree loop, I would like to know if anyone faced this problem and resolved it. Because this MLS message is popping on the screen too often.

Thanks in advance.

Regards

Senthil Natarajan

wong34539 · ‎01-29-2003

This is a good resource to help you.

http://www.cisco.com/warp/customer/473/16.html