12-05-2003 05:01 AM - edited 03-02-2019 12:10 PM
Hi All,
I'm trying to configure 2 x 1700 routers with WIC-1AMs which will dial-up to one another.
The strange thing is the customer has an EPS25B (UK) circuit which I understand immediately trunks the call point-to-point without any numbers being dialled?
Any idea how i could configure this within the 1700 -
Thanks,
Stuart
12-05-2003 12:46 PM
Hello,
since those private services lines are leased for a fixed tariff, regardless of how much they're used, I guess you wouldn´t mind if the two routers are connected all the time. So the ´standard´ configuration for the WIC-1AM would do, I would think. Check out this link for configuration options and examples of this analog card:
Regards,
Georg
12-08-2003 05:37 AM
Thanks Georg,
I'm a little confused as to what numbers to put in for the dial-string, after all anything would do.
May i possibly attach the config for your advice if i end up with any issues?
Cheers,
Stu
12-08-2003 09:03 AM
Configs:
wr t
BTH-1721-1-1#
BTH-1721-1-1#
BTH-1721-1-1#term len 0
BTH-1721-1-1#wr t
Building configuration...
Current configuration : 1521 bytes
!
version 12.3
service config
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname BTH-1721-1-1
!
enable password 7
!
username A1 password 7
username B2 password 7
ip subnet-zero
!
!
!
!
!
!
!
interface FastEthernet0
ip address 10.244.1.101 255.255.224.0
speed auto
!
interface Async1
ip unnumbered FastEthernet0
encapsulation ppp
dialer in-band
dialer string 1
dialer-group 1
async mode interactive
no keepalive
ppp authentication chap
!
ip classless
ip route 10.226.0.0 255.255.224.0 Async1
no ip http server
!
dialer-list 1 protocol ip permit
banner login ^C
*************************************
*************************************
*** ***
*** Private Computer Facility ***
*** Authorised Access Only ***
*** ***
*** All NON-AUTHORISED Users ***
*** Logout IMMEDIATELY ***
*** Thank You ***
*** ***
*************************************
*************************************
BH-RL^C
!
line con 0
password 7
login
line 1
flush-at-activation
modem InOut
transport input all
autoselect ppp
stopbits 1
speed 115200
flowcontrol hardware
line aux 0
line vty 0 4
password 7
login
!
no scheduler allocate
!
end
BTH-1721-1-1#exit
run
Building configuration...
Current configuration : 929 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname RUSSELROAD-G-1
!
enable password 7
!
username A1 password 7
username B2 password 7
ip subnet-zero
!
!
!
!
!
!
!
interface FastEthernet0
ip address 10.226.0.1 255.255.224.0
speed auto
no keepalive
!
interface Async1
ip unnumbered FastEthernet0
encapsulation ppp
dialer in-band
dialer string 1
dialer-group 1
async mode interactive
no keepalive
ppp authentication chap
!
ip classless
ip route 0.0.0.0 0.0.0.0 Async1
no ip http server
!
dialer-list 1 protocol ip permit
!
line con 0
password 7
login
line 1
flush-at-activation
stopbits 1
speed 115200
flowcontrol hardware
line aux 0
line vty 0 4
password 7
login
!
!
end
RUSSELROAD-G-1#
12-08-2003 09:04 AM
Help much appreciated - thank you
Debugs from A-end:
BTH-1721-1-1#show debug
General OS:
Modem control/process activation debugging is on
Dial on demand:
Dial on demand events debugging is on
PPP:
PPP authentication debugging is on
BTH-1721-1-1#term mon
BTH-1721-1-1#
BTH-1721-1-1#
BTH-1721-1-1#ping 10.226.0.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.226.0.1, timeout is 2 seconds:
*Mar 1 02:20:20.167: As1 DDR: place call
*Mar 1 02:20:20.167: As1 DDR: Dialing cause ip (s=10.244.1.101, d=10.226.0.1)
*Mar 1 02:20:20.167: As1 DDR: Attempting to dial 1
*Mar 1 02:20:20.167: CHAT1: Attempting async line dialer script
*Mar 1 02:20:20.167: Modem Registers - IMR:0x0 LED:0x0 RstCntrl:0x0 MSR:0xFF
*Mar 1 02:20:20.167: CHAT1: no matching chat script found for 1
*Mar 1 02:20:20.167: CHAT1: Dialing using Modem script: d0efault-d0ials0cript & System script: none
*Mar 1 02:20:20.167: CHAT1: process started
*Mar 1 02:20:20.171: CHAT1: Asserting DTR
*Mar 1 02:20:20.171: CHAT1: Chat script d0efault-d0ials0cript started.....
Success rate is 0 percent (0/5)
BTH-1721-1-1#
BTH-1721-1-1#
*Mar 1 02:21:20.267: CHAT1: Chat script d0efault-d0ials0cript finished, status
= Connection timed out; remote host not responding
*Mar 1 02:21:20.267: TTY1: Line reset by "Async dialer"
*Mar 1 02:21:20.267: As1 DDR: disconnecting call
*Mar 1 02:21:20.267: TTY1: Modem: (unknown)->HANGUP
*Mar 1 02:21:20.267: TTY1: no timer type 0 to destroy
*Mar 1 02:21:20.267: TTY1: no timer type 1 to destroy
*Mar 1 02:21:20.267: TTY1: no timer type 3 to destroy
*Mar 1 02:21:20.267: TTY1: no timer type 4 to destroy
*Mar 1 02:21:20.267: TTY1: no timer type 10 to destroy
*Mar 1 02:21:20.267: TTY1: no timer type 2 to destroy
*Mar 1 02:21:20.391: TTY1: dropping DTR, hanging up
*Mar 1 02:21:20.391: tty1: Modem: HANGUP->IDLE
*Mar 1 02:21:25.407: TTY1: restoring DTR
BTH-1721-1-1#
BTH-1721-1-1#
*Mar 1 02:21:35.267: As1 DDR: re-enable timeout
BTH-1721-1-1#
BTH-1721-1-1#
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide