WIC-2T - hardware problem?

[tirmatovt]

Hi!

I have a cisco 2610 router connected to satellite modem (CDM-600). Cisco has NM-2W module with WIC-2T card, one port of this card is connected to modem via CAB-SS-530MT=, chassis WIC slot is filled with 2MFT-E1. Everything works fine for several hours. Then serial interface (connected to modem) goes down, and never comes up. I see following messages in the log:

21: Dec 1 19:04:20: %FECPM-3-SCCRESET: SCC reset for int 1/0 at fecpm_serial_stop failed

22: -Traceback= 801DDC08 801DDF30 801DDF94 80010874 8048B05C 8048E708

23: Dec 1 19:04:20: %FECPM-2-SCCFAIL: Init of SCC1 for int 0/0 failed to do fecpm_dma_init

24: -Traceback= 801DDDC0 801DDF44 801DDF94 80010874 8048B05C 8048E708

25: Dec 1 19:04:22: %LINK-3-UPDOWN: Interface Serial1/0, changed state to down

26: Dec 1 19:04:50: %FECPM-3-SCCRESET: SCC reset for int 1/0 at fecpm_serial_stop failed

27: -Traceback= 801DDC08 801DDF30 801DDF94 80010874 8048B05C 8048E708

28: Dec 1 19:04:50: %FECPM-2-SCCFAIL: Init of SCC1 for int 0/0 failed to do fecpm_dma_init

29: -Traceback= 801DDDC0 801DDF44 801DDF94 80010874 8048B05C 8048E708

30: Dec 1 19:05:20: %FECPM-3-SCCRESET: SCC reset for int 1/0 at fecpm_serial_stop failed

31: -Traceback= 801DDC08 801DDF30 801DDF94 80010874 8048B05C 8048E708

32: Dec 1 19:05:20: %FECPM-2-SCCFAIL: Init of SCC1 for int 0/0 failed to do fecpm_scc_ivq_init

33: -Traceback= 801DED38 801DDF3C 801DDF94 80010874 8048B05C 8048E708

Does anybody have an idea on what is happening here? Any hints will be greatly appreciated!

[thisisshanky]

This is as much as I can find,

http://www.cisco.com/en/US/partner/products/sw/iosswrel/ps5207/products_system_message_guide_chapter09186a00801ae2c9.html#wp814296

[tirmatovt]

Thanks for replying.

Ouch, your link says I have invalid login/password. I think, I must have some privileged account on cisco.com to access this information? :-(

[mparies05]

Have a look @ the error message decoder:

Showing 1-4 of 4 results

Page:               1

1. %FECPM-2-SCCFAIL: Init of SCC[dec] for int [dec]/[dec] failed to do [chars] The software has failed to initialize or restart a Signaling Connection Control (SCC) of a serial interface on the Fast Ethernet Combination Port Module device driver network module. Recommended Action: Clear the serial interface. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information. Related documents- No specific documents apply to this error message.

2. %FECPM-2-SCCFAIL: Init of SCC[dec] for int [dec]/[dec] failed to do [chars] The software has failed to initialize or restart a Signaling Connection Control (SCC) of a serial interface on the Fast Ethernet Combination Port Module device driver network module. Recommended Action: Clear the serial interface. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information. Related documents- No specific documents apply to this error message.

3. %FECPM-2-SCCFAIL: Init of SCC[dec] for int [chars] failed to do [chars] The software failed to initialize/restart an SCC of a serial interface on FECPM. Recommended Action: Clear the serial interface.If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit athttp://www.cisco.com/pcgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/http://tools.cisco.com/ServiceRequestTool/create/, or contact your Cisco technical support representative and provide the representative with the gathered information. Related documents- No specific documents apply to this error message.

4. %FECPM-2-SCCFAIL: Init of SCC[dec] for int [chars] failed to do [chars] The software failed to initialize/restart an SCC of a serial interface on FECPM. Recommended Action: Clear the serial interface.If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit athttp://www.cisco.com/pcgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/http://tools.cisco.com/ServiceRequestTool/create/, or contact your Cisco technical support representative and provide the representative with the gathered information. Related documents- No specific documents apply to this error message.

Showing 1-4 of 4 results

Page:       1

[paolo bevilacqua]

2601 and its interfaces is now 16 years old. Wouldn't be time for having it replaced anyway ?