Hi Guys,
We are trying to breakout the 4X10G optics on the NCS-57B1-5DSE-SYS but system throwing the below mentioned error.
<0-71> configure end port
RP/0/RP0/CPU0:ios#sh run hw-module port-range 0 1 ?
instance card instance of MPA's
location fully qualified location specification
RP/0/RP0/CPU0:ios#sh run hw-module port-range 0 1 location ?
0/RP0/CPU0 fully qualified location specification
WORD fully qualified location specification
RP/0/RP0/CPU0:ios#sh run hw-module port-range 0 1 location 0/RP0/CPU0
% Incomplete command.
RP/0/RP0/CPU0:ios#sh run hw-module port-range 0 1 location 0/RP0/CPU0 ?
mode port mode 40-100, 400, 2x100, 4x10, 4x25, 4x10-4x25, 1x100, 2x100-PAM4, 3x100, 4x100
RP/0/RP0/CPU0:ios#sh run hw-module port-range 0 1 location 0/RP0/CPU0 mode ?
WORD port mode 40-100, 400, 2x100, 4x10, 4x25, 4x10-4x25, 1x100, 2x100-PAM4, 3x100, 4x100
RP/0/RP0/CPU0:ios#sh run hw-module port-range 0 1 location 0/RP0/CPU0 mode 4x10
Wed Aug 18 10:01:11.302 UTC
hw-module port-range 0 1 instance 0 location 0/RP0/CPU0 mode 4x10
RP/0/RP0/CPU0:ios#sh run hw-module port-range 2 3 location 0/RP0/CPU0 mode 4x10
Wed Aug 18 10:01:19.167 UTC
% No such configuration item(s)
RP/0/RP0/CPU0:ios# conf t
Wed Aug 18 10:01:33.688 UTC
RP/0/RP0/CPU0:ios(config)#hw-module port-range 4 5 location 0/RP0/CPU0 mode 4x10
RP/0/RP0/CPU0:ios(config)#commit
Wed Aug 18 10:01:43.007 UTC
\
% Failed to commit one or more configuration items. Please issue 'show configuration failed [inheritance]' from this session to view the errors
RP/0/RP0/CPU0:ios(config)#
RP/0/RP0/CPU0:ios(config)#
RP/0/RP0/CPU0:ios(config)#
RP/0/RP0/CPU0:ios(config)#
RP/0/RP0/CPU0:ios(config)#
RP/0/RP0/CPU0:ios(config)#
RP/0/RP0/CPU0:ios(config)#
RP/0/RP0/CPU0:ios(config)#
RP/0/RP0/CPU0:ios(config)#
RP/0/RP0/CPU0:ios(config)#\
^
% Invalid input detected at '^' marker.
RP/0/RP0/CPU0:ios(config)#
RP/0/RP0/CPU0:ios(config)#shwo conffa
^
% Invalid input detected at '^' marker.
RP/0/RP0/CPU0:ios(config)#show configuration failed
Wed Aug 18 10:07:19.829 UTC
!! APPLY ERRORS: This configuration was accepted by the system,
!! but errors occurred when the system attempted to make the
!! configuration operational. The individual errors for each
!! failed configuration command can be found below. These errors
!! will cause an inconsistency between the system's running
!! configuration and its operational state, which may be addressed
!! by using the 'no' form of the command to remove it from the
!! running configuration.
hw-module port-range 4 5 instance 0 location 0/RP0/CPU0 mode 4x10
!!% The process 'optics_driver' took too long to respond to an apply request and was timed out
end
RP/0/RP0/CPU0:ios(config)#
RP/0/RP0/CPU0:ios(config)#
RP/0/RP0/CPU0:ios(config)#
