Hi,
I have referred lots of details on internet for simple config of my SG300-28 switch i.e. "Inter VLAN routing on cisco SG300", hava found lots of solutions and many of them are so simple on paper but when I try them I failed. Please help me find where I am making a mist
|
Creat two VLAN 1)192.168.1.254 and 2) 192.168.2.254
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
REQUIREMENT
|
|
|
|
|
|
|
|
|
|
|
VLAN 1 (default VLAN)
|
|
|
|
|
|
|
|
|
|
IP
|
192.168.1.254 - default
|
|
|
|
|
|
|
|
|
|
Name
|
VLAN 1 (default VLAN)
|
|
|
|
|
|
|
|
|
|
Client
|
192.168.1.100
|
|
|
|
|
|
|
|
|
|
Client gateway
|
192.168.1.254
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VLAN 2 (user created)
|
|
|
|
|
|
|
|
|
|
IP
|
192.168.2.254
|
|
|
|
|
|
|
|
|
|
Name
|
VLAN 2 (TEST)
|
|
|
|
|
|
|
|
|
|
Client
|
192.168.2.100
|
|
|
|
|
|
|
|
|
|
Client gateway
|
192.168.2.254
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Needs intervlan routing so that I can get ping reply from 192.168.1.100 when try to ping from 192.168.2.100
|
|
|
|
|
similarly from 192.168.2.100 when I try to ping from 192.168.1.100
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
STEPS I AM FOLLOWING
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Unbox the switch and login to it using browser 192.1681.254 (google chrome)
|
|
|
|
|
|
|
|
Change the password as asked when login frirst time
|
|
|
|
|
|
|
|
|
|
Change the switch mode from L2 to L3
|
|
|
|
|
|
|
|
|
|
On saving switch reboots and after reboot I can see the switch mode is L3 nos
|
|
|
|
|
|
|
|
I go to create VLAN
|
|
|
|
|
|
|
|
|
|
Now I can see VLAN 1 - default with IP address 192.168.1.254
|
|
|
|
|
|
|
|
|
|
I add new VLAN i.e VLAN 2, name - TEST
|
|
|
|
|
|
|
|
|
|
On checking the port types / assignement I can see all ports are untagged and trunk for VLAN -1
|
|
|
|
|
|
|
I go to VLAN 2 and I make port 2 untagged member of VLAN 2 and the same is traunk type by default
|
|
|
|
|
|
|
|
Now I change Port 1 and 2 both as Access by editing them
|
|
|
|
|
|
|
|
|
|
Now finally switch port 1 is an untanned , access port of VLAN -1 where I am connecting my PC with IP 192.168.1.100
|
|
|
|
|
Switch port 2 is an untanned , access port of VLAN -2 where I am connecting my PC with IP 192.168.2.100
|
|
|
|
|
|
Now I go to IP interface and select VLAN 2 to give an IP address to it i.e 192.168.2.254 but when I selecet "apply" immediately switch hangs and I cant do any thing
|
|
I have to reboot the switch with power off / on
|
|
|
|
|
|
|
|
|
|
Same things repeats every time
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Please help
|
|
|
|
|
|
|
|
|
|
