07-18-2016 03:16 PM
Hi,
I configured Cisco 877w with very basic settings for ADSL2, LAN and Wifi users. I was using Telnet to configure it. Router disconnected from telnet when i gave following cmd in Int VLAN 1
Router (config-if)# bridge-group 1
Later, i removed ip add from VLAN1 and setup BVI 1 from console.
Now, i cannot ping, access or telnet to router from LAN. Laptops or mobiles cannot detect/see Wifi SSID . I am sure it has connected with ISP because before Wifi setup i was using it for internet and now can see ppp light.
Please help me, where i did mistake or need new cmds.
running-config as under.
Regards
agkhan
running-config
Building configuration...
Current configuration : 2227 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R1
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$aV3$%6ght7*olKMEUzFHqLtL0
!
no aaa new-model
!
resource policy
!
clock timezone PCTime 8
ip subnet-zero
ip cef
no ip dhcp use vrf connected
!
ip dhcp pool Dhakan
network 10.0.0.0 255.255.255.0
default-router 10.0.0.138
dns-server 10.0.0.138 139.130.4.4 203.50.2.71 8.8.8.8 4.2.2.2
!
!
no ip domain lookup
ip name-server 139.130.4.4
ip name-server 203.50.2.71
ip name-server 4.2.2.2
ip name-server 8.8.8.8
ip name-server 10.0.0.138
vpdn enable
!
!
!
!
!
!
!
bridge irb
!
!
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 8/35
pppoe-client dial-pool-number 1
!
dsl operating-mode auto
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Dot11Radio0
no ip address
!
ssid freestyle
authentication open
!
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface Vlan1
no ip address
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1412
bridge-group 1
bridge-group 1 spanning-disabled
!
interface Dialer1
mtu 1492
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
ppp authentication chap pap callin
ppp chap hostname aaaaaaaa@bigpond.com
ppp chap password 0 XXXXXXXX
ppp pap sent-username aaaaaaaa@bigpond.com password 0 XXXXXXXX
!
interface BVI1
description LAN & WAN with Wifi.
ip address 10.0.0.138 255.255.255.0
ip nat inside
ip virtual-reassembly
!
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
!
no ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer1 overload
!
access-list 1 permit any
!
control-plane
!
!
line con 0
logging synchronous
no modem enable
line aux 0
line vty 0 4
password 000000000
login
!
scheduler max-task-time 5000
end
07-18-2016 03:56 PM
I cant quite follow what you are trying to achieve, why do you want to have this BVI interface?
07-18-2016 04:15 PM
Thank you for reply.
I just want to configure Wifi LAN/interface, DHCP for LAN user and ADSL in router. I took different references to configure Wifi from internet but I think these are not working.
regards
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide