About Dennis Mink

Dennis Mink · ‎10-23-2019

Typical codec mismatch behaviour. Chech the apllicable region settings across the ic trunk

Dennis Mink · ‎10-23-2019

Send debug ccsip message please. The ringi g follows after the trying is received and the responder can actuall ring the destionation. Without debugs it is not possible to determine wherr the false positive ringing occurs. Or if this is expected behaviour

Dennis Mink · ‎10-23-2019

Whats sysyem.is this on and what phone type?

Dennis Mink · ‎10-16-2019

From call manager 10 there are some native queueing fwautures available when calling into a hunt pilot. This might suit your needs and is cheaper than spinning up a uccx box

Dennis Mink · ‎10-09-2019

Have you tried a transfer from unity to an internal number? Try this first. Could be a css issue on your unity cti routepoints or sip trunk to and from unity

Dennis Mink · ‎10-09-2019

This is most likely a routing issue. If your cube is flow through. Your cube will need to be able to route to all phones and vice versa. Also if you have a fw in the path allow rtp from cube to all voice subnets

Dennis Mink · ‎10-09-2019

What are your internal codecs g711? Sounds like codec mismatch

Dennis Mink · ‎10-05-2019

What is in the path between agents and cucm? Is it a wan link that goes down? For example.

Dennis Mink · ‎10-01-2019

If that is all the info provided. It could be ip address issue. What vlan is the access point in?

Dennis Mink · ‎09-29-2019

seeing there is liitle information, I am gonna have a stab at this: D EX 10.54.180.0/24 [170/3072] via 10.0.0.3, 00:14:06, Vlan760 [170/3072] via 10.0.0.2, 00:14:06, Vlan760 both routes have admin distance of 170 (external EIGRP). so bot routes are equal cost. as soon as you change the admin distance to 200, it no longer appears in the routing table because the remaining route with admin distance 170 is cheaper. This is how i interpret this

Dennis Mink · ‎09-21-2019

If the routers port has one ip address then tagging is not needed. If you have subinterfaces with ip addresses on the one physical port then yes you need to tag

Dennis Mink · ‎09-19-2019

There are no HP switches that stack up against anything in the cisco fleet. The only reason people buy hp Is cos they are cheap.

Dennis Mink · ‎09-17-2019

For upgrade path its best to read the release notes of the version you want to go to. This will tell you if the upgrade is stepped or not

Dennis Mink · ‎09-16-2019

Snmp

Dennis Mink · ‎09-16-2019

As always it depends. You need a minimum of 1. And 2 to make it redundant. Then you might want to add more depending on geographical spread. How big is your deployment?

Dennis Mink · 10-23-2019

Typical codec mismatch behaviour. Chech the apllicable region settings across the ic trunk

Dennis Mink · 10-23-2019

Send debug ccsip message please. The ringi g follows after the trying is received and the responder ...

Dennis Mink · 10-23-2019

Whats sysyem.is this on and what phone type?

Dennis Mink · 10-16-2019

From call manager 10 there are some native queueing fwautures available when calling into a hunt pil...

Dennis Mink · 10-09-2019

Have you tried a transfer from unity to an internal number? Try this first. Could be a css issue on ...

Dennis Mink · 10-09-2019

This is most likely a routing issue. If your cube is flow through. Your cube will need to be able to...

Dennis Mink · 10-09-2019

What are your internal codecs g711? Sounds like codec mismatch

Dennis Mink · 10-05-2019

What is in the path between agents and cucm? Is it a wan link that goes down? For example.

Dennis Mink · 10-01-2019

If that is all the info provided. It could be ip address issue. What vlan is the access point in?

Dennis Mink · 09-29-2019

seeing there is liitle information, I am gonna have a stab at this: D EX 10.54.180.0/24 [170/3072] v...

Dennis Mink · 09-21-2019

If the routers port has one ip address then tagging is not needed. If you have subinterfaces with ip...

Dennis Mink · 09-19-2019

There are no HP switches that stack up against anything in the cisco fleet. The only reason people b...

Dennis Mink · 09-17-2019

For upgrade path its best to read the release notes of the version you want to go to. This will tell...

Dennis Mink · 09-16-2019

Snmp

Dennis Mink · 09-16-2019

As always it depends. You need a minimum of 1. And 2 to make it redundant. Then you might want to ad...

Date Registered	‎10-15-2006 10:31 AM
Date Last Visited	‎10-23-2019 05:15 AM
Total Messages Posted	3,776
Total Helpful Votes Received	3154

Re: Calls failure

Re: SIP Call rings continues but destin...

Re: alerting name not displayed while o...

Re: IVR with Only CUCM (?)

Re: Cisco Unity Connection - Greeting I...

Re: cucm wont send or receive voice thr...

Re: conference issue

Re: Cisco Softphones getting Unregister...

Re: Wireless connectivity issue

Re: Redistribute Static into EIGRP

Re: Tagged or Untagged Trunk?

Re: Cisco 9600 switches vs HP switches

Re: Failed upgrade CISCO IOS XE version...

Re: How to check the calls in a gateway...

Re: Minimum servers in calla manager cl...

Re: Calls failure

Re: SIP Call rings continues but destination phone is switched off

Re: alerting name not displayed while on call waiting

Re: IVR with Only CUCM (?)

Re: Cisco Unity Connection - Greeting Input to External Number

Re: cucm wont send or receive voice through working sip trunk

Re: conference issue

Re: Cisco Softphones getting Unregistered frequently

Re: Wireless connectivity issue

Re: Redistribute Static into EIGRP

Re: Tagged or Untagged Trunk?

Re: Cisco 9600 switches vs HP switches

Re: Failed upgrade CISCO IOS XE version 16.06.06 to 16.09.04 on #CISCO CSR 1000v

Re: How to check the calls in a gateway for specific time

Re: Minimum servers in calla manager cluster should contain