cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1316
Views
0
Helpful
3
Replies

7206VXR router POS interface loopback

Pradeep H A
Level 1
Level 1

Hi All,

We have a 7206vxr router with a pos interface: its PA-POS-1OC3 card currently in up/down status:

We already repalced the card but still same (up/down) condition.

R01#sh int pos 1/0

POS1/0 is up, line protocol is down

  Hardware is Packet over Sonet

  Description: PPP link to MPLS PE

  Internet address is *****************

  MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation PPP, LCP ACKsent, crc 32, loopback not set

  Keepalive set (10 sec)

  Scramble enabled

  Last input 00:00:05, output never, output hang never

  Last clearing of "show interface" counters 4d12h

  Input queue: 0/1000/0/0 (size/max/drops/flushes); Total output drops: 0

  Queueing strategy: fifo

  Output queue: 4/40 (size/max)

  5 minute input rate 0 bits/sec, 0 packets/sec

  5 minute output rate 0 bits/sec, 0 packets/sec

     75362 packets input, 1356464 bytes, 0 no buffer

     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

              0 parity

     4 input errors, 7 CRC, 0 frame, 0 overrun, 0 ignored, 3 abort

     1628 packets output, 25438 bytes, 0 underruns

     0 output errors, 0 applique, 5469 interface resets

     0 output buffer failures, 0 output buffers swapped out

     1 carrier transitions

I tried putting an internal loop on the interface (new card): still it doesnt come up! as per my knowledge internal loopback means a loop within the card right? then its not coming up for internal loop also means even the new card has gone faulty or do I need replace the whole chasis?

R01#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R01(config)#int pos 1/0
R01(config-if)#loopback ?
  internal  internal
  line      line

R01(config-if)#loopback internal

R01#sh int POS1/0

POS1/0 is up, line protocol is down

  Hardware is Packet over Sonet

  Description: PPP link to MPLS PE

  Internet address is 192.168.211.49/30

  MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation PPP, LCP Listen, crc 32, loopback set (internal)

  Keepalive set (10 sec)

  Scramble enabled

  Last input 00:00:54, output never, output hang never

  Last clearing of "show interface" counters 4d12h

  Input queue: 0/1000/0/0 (size/max/drops/flushes); Total output drops: 0

  Queueing strategy: fifo

  Output queue: 0/40 (size/max)

  5 minute input rate 0 bits/sec, 0 packets/sec

  5 minute output rate 0 bits/sec, 0 packets/sec

     75090 packets input, 1351616 bytes, 0 no buffer

     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

              0 parity

     4 input errors, 7 CRC, 0 frame, 0 overrun, 0 ignored, 2 abort

     1628 packets output, 25438 bytes, 0 underruns

     0 output errors, 0 applique, 5431 interface resets

     0 output buffer failures, 0 output buffers swapped out

     0 carrier transitions

3 Replies 3

paolo bevilacqua
Hall of Fame
Hall of Fame

Do something else: loopback the circuit.

The objective is to prove to telco that the circuit is faulty, not the router.

vblaha
Level 1
Level 1

Did you ever figure this out? 

Yes Vblaha,

We replaced the chasis & WIC card with same configuration. The link came up.

So basically I understand it was chasis fault that made the WIC card not respond to even an internal loopback

Any more suggestions on this?

Thanks

Review Cisco Networking for a $25 gift card