We have a cisco 7600 router that have a 7600-SIP-200 module installed on it slot 3 when we try to test the router we have the module give the ollowin error:
% module 3 is operationally off (Module Failed SCP dnld)
Knowing that we have another router the same model exactly and the IOS and Bootstrap image and is wirking fine here is the show version and show module :
Router#show version
Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SRA6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Thu 25-Oct-07 19:13 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)S4, RELEASE SOFTWARE (fc1)
Router uptime is 25 minutes
Uptime for this control processor is 25 minutes
Time since Router switched to active is 24 minutes
System returned to ROM by power cycle (SP by power on)
System image file is "bootdisk:s72033-ipservicesk9_wan-mz.122-33.SRA6.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco CISCO7609-S (R7000) processor (revision 1.0) with 458720K/65536K bytes of memory.
Processor board ID FOX1147H0WS
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from s/w reset
1 Virtual Ethernet interface
28 Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
Router#show module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL1152BGVW
3 0 4-subslot SPA Interface Processor-200 7600-SIP-200 JAE12034Q8V
5 2 Supervisor Engine 720 (Active) WS-SUP720-3B JAF1150ABAA
6 2 Supervisor Engine 720 (Warm) WS-SUP720-3B JAF1150ABFJ
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 001e.7ae2.817c to 001e.7ae2.8193 3.1 12.2(18r)S1 12.2(33)SRA6 Ok
3 001e.7a5c.3d00 to 001e.7a5c.3d3f 2.303 Unknown Unknown PwrDown
5 001b.d50d.a420 to 001b.d50d.a423 5.6 8.5(2) 12.2(33)SRA6 Ok
6 001b.d50d.a474 to 001b.d50d.a477 5.6 8.5(2) 12.2(33)SRA6 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 Centralized Forwarding Card WS-F6700-CFC JAF1150AMMP 4.0 Ok
5 Policy Feature Card 3 WS-F6K-PFC3B JAF1149010Z 2.3 Ok
5 MSFC3 Daughterboard WS-SUP720 JAF115000MM 3.1 Ok
6 Policy Feature Card 3 WS-F6K-PFC3B JAF115001GW 2.3 Ok
6 MSFC3 Daughterboard WS-SUP720 JAF115000P3 3.1 Ok
Mod Online Diag Status
---- -------------------
1 Pass
3 Not Applicable
5 Pass
6 Pass
I did everything I know :
Check the hardware and software compatibility do reset to the module.
do I have to install any specific package to run this module?
I appreciate your Advice.
