cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Community Helping Community

14350
Views
0
Helpful
15
Replies
Beginner

Asymmetric Routing Issue

Hi All,

I'm currently having asymmetric routing issue on my network. We are taking over few departments of a company. Currently the users access our servers via public Internet which are Nated back to our private addresses on our network. This company for some wired reason is using public IP addressing internally. We have installed a LES point to point link with this company so that the users can access the network resources directly. I have installed a firewall between us and them. Company's current networks team doesn't want to use our private addressing over their network hence I had to Nat few of our server IPs to public IP addresses to be available on their network.

The issue is when the users need to connect to any of the other servers then come through our public facing firewall and then to our core. In order to forward the traffic to the LES link firewall I had to route the traffic to it which automatically routes the traffic coming from the company's network via our public firewall hence creating a asymmetric route on the way back.

Ideally the traffic coming from public firewall should go back to the source same way and the traffic coming from LES firewall should go back to the source same way. Can someone advise how can I route the traffic for company's network (10.134.x.x) back out the same way as it came, either via public firewall or the LES link firewall?

Many thanks in advance.

1 ACCEPTED SOLUTION

Accepted Solutions
Beginner

Asymmetric Routing Issue

Thanks,

Simple;

Policy base route traffic from the source IP's of the red servers back to the public firewall. In the order of operation PBR comes before routing so should work.

Simon

View solution in original post

15 REPLIES 15
Beginner

Re:Asymmetric Routing Issue

Can you supply a quick diagram. I have to admit I cant understand what you've described.


Sent from Cisco Technical Support Android App

Beginner

Asymmetric Routing Issue

Hi,

Please see below the diagram. Hope it makes sense.

Beginner

Asymmetric Routing Issue

Thanks,

Simple;

Policy base route traffic from the source IP's of the red servers back to the public firewall. In the order of operation PBR comes before routing so should work.

Simon

View solution in original post

Beginner

Asymmetric Routing Issue

Hi Simon,

Thank you for your reply.

The company users are base on 10.146.0.0/16 range hence will it be possible to route the entire traffic for both these server groups?

Beginner

Asymmetric Routing Issue

Hi,

You asked if you could route tracffic received by each firewall back to their respective firewalls, not for the whole subnet.

My assumptions are you have an SVI shared across both cores running HSRP, hence you will need to do the following on both core's.  Levae the default route alone on both core's also.

Create an acl;

ip access-list extended PBR

permit ip host 10.134.117.19 10.146.0.0 255.255.0.0

permit ip host 10.134.117.20 10.146.0.0 255.255.0.0

permit ip host 10.134.117.21 10.146.0.0 255.255.0.0

Create a route-map

route-map PBR permit 10

match ip address PBR

set ip next-hop x.x.x.x (where x is the inside IP of public firewall)

On the servers SVI;

interface vlan 134

ip policy route-map PBR

That should do it.

Simon

Beginner

Asymmetric Routing Issue

Hi Simon,

I have setup the below access list for the company's network on our core switch 1

ip access-list extended ACL-Servers

permit ip host 192.168.55.114 10.146.0.0 0.0.255.255

permit ip host 192.168.55.12 10.146.0.0 0.0.255.255

permit ip host 192.168.55.129 10.146.0.0 0.0.255.255

permit ip host 192.168.50.209 10.146.0.0 0.0.255.255

permit ip host 192.168.50.170 10.146.0.0 0.0.255.255

permit ip host 192.168.50.175 10.146.0.0 0.0.255.255

permit ip host 192.168.50.178 10.146.0.0 0.0.255.255

permit ip host 192.168.50.179 10.146.0.0 0.0.255.255

permit ip host 192.168.50.181 10.146.0.0 0.0.255.255

permit ip host 192.168.37.254 10.146.0.0 0.0.255.255

route-map RM-Servers permit 10

match ip address ACL-Servers-Barnet

set ip next-hop 172.20.109.1 (IP address of the Company facing firewall)

!

route-map RM-Servers permit 20

CSW1(config)# do sh run int vlan 50

Building configuration...

Current configuration : 236 bytes

!

interface Vlan50

description Servers

ip address 192.168.50.1 255.255.255.0

ip helper-address 192.168.55.114

ip policy route-map RM-Servers

end

CSW1(config)# do sh run int vlan 55

Building configuration...

Current configuration : 199 bytes

!

interface Vlan55

ip address 192.168.55.1 255.255.255.0

ip helper-address 192.168.50.2

ip policy route-map RM-Servers

end

But still am unable to route the traffic for the above servers to 172.20.109.1.

Beginner

Asymmetric Routing Issue

The name of your acl and the acl specified in the route-map do not match.

Simon

Beginner

Asymmetric Routing Issue

Sorry my bad. I have amended it now but still no joy. Do i have to enable local policy for this?

Highlighted
Beginner

Asymmetric Routing Issue

I am getting packets matches but i can't see it hitting our firewall.

CSW1#sh route-map

route-map RM-Servers, permit, sequence 10

  Match clauses:

    ip address (access-lists): ACL-Servers-Barnet

  Set clauses:

    ip next-hop 172.20.109.1

  Policy routing matches: 4109 packets, 427523 bytes

route-map RM-Servers, permit, sequence 20

  Match clauses:

  Set clauses:

  Policy routing matches: 155487 packets, 17976974 bytes

Beginner

Asymmetric Routing Issue

Show ip route 172.20.109.1 ?

Does the firewall have a route back to the 10.146.0. subnet also over the internet ?

Simon

Beginner

Asymmetric Routing Issue

CSW1#sh ip route 172.20.109.1

Routing entry for 172.20.109.0/30

  Known via "static", distance 1, metric 0

  Redistributing via eigrp 200, ospf 1

  Advertised by eigrp 200

                ospf 1 subnets

  Routing Descriptor Blocks:

  * 192.168.50.2

      Route metric is 0, traffic share count is 1

Yes the fiewall has a route outside 0.0.0.0 0.0.0.0 10.146.120.201 1

Beginner

Asymmetric Routing Issue

Sh run | inc ip route

Your firewall IP is in the same subnet as the servers?

Cheers

Beginner

Re: Asymmetric Routing Issue

No the firewall isn't on the same subnet but there is a route from the core switch to this firewall.

Sent from Cisco Technical Support iPad App

Beginner

Re:Asymmetric Routing Issue

Ok so the next hop from the core to the firewall also needs the pbr config.

Sent from Cisco Technical Support Android App

CreatePlease to create content
Content for Community-Ad
FusionCharts will render here