cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1386
Views
15
Helpful
5
Replies

C887VA-WD-E-K9 VDSL firmware vectoring question

Luca Pecchiari
Level 1
Level 1

Hello,

 

i have a C887VA-WD-E-K9 and i am planning to move the line from ADSL to VDSL2.

 

Now i run this (c800-universalk9-mz.SPA.157-3.M6.bin);

 


Firmware Source File Name
-------- ------ ----------
VDSL embedded VDSL_LINUX_DEV_01212008

Modem FW Version: 4.14L.04A
Modem PHY Version: A2pv6C039t.d24o_rc1

 

Basically i need to know if the VDSL firmware that is now loaded support Vectoring ( ITU-T G.993.5), if not can you point me to the right firmware please?

 

On a post i find out that "To support VDSL vectoring (ITU-T G.993.5) your VDSL (modem) firmware needs to be at least 38h, ie. you need upgrade" but i am not able to compare version...

 

Thank you

2 Accepted Solutions

Accepted Solutions

Hello,

 

looks like you need B2pvC038h3:

 

--> supports the following features:
• G.993.2 (VDSL2) protocol
– PTM and ATM mode
– Annex B over ISDN band plans
– Profiles supported: 8a/b/c/d, 12a/b and 17a
– US0
– Diagnostics mode/DELT
– Bitswaps, SRA and SOS/ROC
– FEXT Equalized UPBO
– Dying Gasp
– INM
– PhyR and G.INP (Framing Type 1)
– SRA/SoS+G.INP
– Virtual Noise
– G.Vector (G.993.5) and G.Vector Friendly (G.993.2 Annex Y)
– Alternate Electrical Length Measurement

View solution in original post

5 Replies 5

balaji.bandi
Hall of Fame
Hall of Fame

Personally, I do not believe your model support that ITU (ITU-T G.993.5)

 

you can look the datasheet.

 

https://www.cisco.com/c/en/us/products/collateral/routers/800-series-routers/data_sheet_c78-613481.html

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Luca Pecchiari
Level 1
Level 1

i found this

 

https://www.cisco.com/c/en/us/products/collateral/routers/800-series-routers/datasheet-c78-734157.html

 

Where my model is listed and it seem that the ITU-T G.993.5 is supported by 38H, but i cannot understand what is the version to get of the firmware

 

Hello,

 

looks like you need B2pvC038h3:

 

--> supports the following features:
• G.993.2 (VDSL2) protocol
– PTM and ATM mode
– Annex B over ISDN band plans
– Profiles supported: 8a/b/c/d, 12a/b and 17a
– US0
– Diagnostics mode/DELT
– Bitswaps, SRA and SOS/ROC
– FEXT Equalized UPBO
– Dying Gasp
– INM
– PhyR and G.INP (Framing Type 1)
– SRA/SoS+G.INP
– Virtual Noise
– G.Vector (G.993.5) and G.Vector Friendly (G.993.2 Annex Y)
– Alternate Electrical Length Measurement

Luca Pecchiari
Level 1
Level 1

i dig a bit more and fint out that those release support it.

 

25-May-2016 VA_A_39t_B_35j_24m

12-Apr-2016 VA_A_39d_B_38h3_24h_1.bin

28-Jul-2015 VA_A_39h_B_38h3_24h_j.bin

31-Jul-2014 VA_A_39d_B_38h3_24h.bin

29-Jul-2014 VA_A_38q_B_38r1_24j.bin

01-Nov-2013 VA_A_38k1_B_38h_24g1.bin

 

may be someone will find this useful.

 

As they change the line i will post the firmware used.

 

Thank you all again

Review Cisco Networking for a $25 gift card