12-04-2013 09:09 AM - edited 03-04-2019 09:45 PM
We configure a cisco 819 as follow:
*************
chat-script hspa "" "AT!SCACT=1,1" TIMEOUT 60 "OK"
interface Cellular0
ip address negotiated
encapsulation slip
dialer in-band
dialer idle-timeout 0
dialer string hspa
dialer-group 1
async mode interactive
line 3
script dialer hspa
modem InOut
no exec
rxspeed 21600000
txspeed 5760000
**************
the following output show that the chat-script is correctly working
*************
yourname#start-chat hspa 3
yourname#
*Dec 4 17:07:02.019: CHAT3: Matched chat script hspa to string hspa
*Dec 4 17:07:02.019: CHAT3: Asserting DTR
*Dec 4 17:07:02.019: CHAT3: Chat script hspa started
*Dec 4 17:07:02.019: CHAT3: Sending string: AT!SCACT=1,1
*Dec 4 17:07:02.019: CHAT3: Expecting string: OK
*Dec 4 17:07:02.019: CHAT3: Completed match for expect: OK
*Dec 4 17:07:02.019: CHAT3: Chat script hspa finished, status = Success
yourname#sh cellular 0 connection
Data Transmitted = 0 bytes, Received = 0 bytes
Profile 1, Packet Session Status = ACTIVE
IP address = 10.147.5.124
Primary DNS address = 212.98.37.131
Secondary DNS address = 194.230.55.97
Negotiated QOS Parameters:
Precedence = Normal Priority, Delay = Class 3
Reliability = Unack GTP, LLC, Ack RLC, Protected data
Peak = 256 kB/sec, Mean = 50000 kB/hr
Traffic Class = Interactive
Uplink Max = 11.5Mbps, Guaranteed = Subscribed
Downlink Max = 42Mbps, Guaranteed = Subscribed
Max SDU size = 1500 bytes
SDU error ratio = 1E-4, BER = 1E-5
**********
but on the cellular0 interface we do not get any ip address....
Any suggestion or ideas?
thank you!
***********
yourname#sh ip int c0
Cellular0 is up, line protocol is up
Internet address will be assigned dynamically by the network
Broadcast address is 255.255.255.255
********************
yourname#sh ver
Cisco IOS Software, C800 Software (C800-UNIVERSALK9-M), Version 15.2(4)M4, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Thu 20-Jun-13 16:14 by prod_rel_team
ROM: System Bootstrap, Version 15.1(4r)M, RELEASE SOFTWARE (fc1)
yourname uptime is 19 minutes
System returned to ROM by power-on
System image file is "flash:c800-universalk9-mz.SPA.152-4.M4.bin"
Cisco C819HG+7-K9 (revision 3.0) with 492620K/31667K bytes of memory.
Processor board ID FCZ1743C24B
4 FastEthernet interfaces
1 Gigabit Ethernet interface
1 Serial(sync/async) interface
1 terminal line
1 Virtual Private Network (VPN) Module
1 Cellular interface
DRAM configuration is 32 bits wide
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash (Read/Write)
***************
01-21-2014 07:40 AM
Do you mind posting your current Run Configuration?
01-22-2014 12:58 AM
hi misha,
sorry not updating this thread.
the 3g modem configuration was correct, the interface c0 came up after doing a ping so we configured an sla.
01-22-2014 06:06 AM
Hello,
Can I ask you for what IOS are you running this on? I am currently experiencing the same issue with IOS
Version 15.2(4)M4. I am trying to determine whether it is the IOS that's preventing me from using similar configurations that other people posted, which work for them, but not for me.
01-22-2014 01:04 PM
Yes, you need to initiate the traffic for this to work. I have done a lot of POC on this and have a blueprint config if someone needs it.
Also, I ended up writing an EEM script to initiate the traffic as soon as router comes up and modem dials out.
Have a look at this for the EEM script write up. Please change the timers as needed.
https://techzone.cisco.com/t5/Cellular-Module/Yet-Another-Cellular-Modem-Recovery-Script/ta-p/287802
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: