03-01-2007 12:31 AM - edited 03-03-2019 03:59 PM
Hello,
I have a cisco 837, I am trying to put factory defaults settings but when I finish , I can?t reach the router ip (it should be 10.10.10.1 ?),I can connect to router only by com port, and I don?t know what is the problem. Please help
Solved! Go to Solution.
03-01-2007 09:18 AM
Router>enable
Router#conf t
Router(config)#interface e0
Router(config-if)#ip address 10.10.10.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#exit
Router#copy run start
Type the commands as you see them and pay attention to the prompts. Im not a big fan of the gui, you might want to learn how to use the cli.
03-01-2007 12:37 AM
Hi Victor ,
Are you getting any messages after resetting it to factory default settings..
Plz check the below link for how to reset a router to factory defaults.
http://www.cisco.com/en/US/products/sw/iosswrel/ps5187/products_tech_note09186a00802017a1.shtml
HTH
satish
03-01-2007 01:34 AM
I do first method, and when I trying to connect to router via explorer I can?t reach router.
If I do 2 method I can?t reach the router too.
When I put some command in hyperterminal I get next message:
Translating "controllers"...domain server (255.255.255.255)
% Unknown command or computer name, or unable to find computer address
How I can put 10.10.10.1 in the server ip to connect it via Explorer ?
Thanks
03-01-2007 03:30 AM
Hi Victor ,
Plz check the below link for blocking the message which is apprearing on the consloe.
http://www.cisco.com/en/US/products/hw/routers/ps133/products_tech_note09186a00802015c8.shtml
HTH
satish
03-01-2007 04:12 AM
Hi and thanks for reply,
When I do runnin-config I get :
Current configuration : 840 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
!
resource policy
!
!
!
ip cef
!
!
resource policy
et2, chan
!d
!
!
!
!
!
!
interface Ethernet0
no ip address
shutdown
hold-queue 100 out
!
interface Ethernet2
no ip address
shutdown
hold-queue 100 out
!
interface ATM0
no ip address
shutdown
no atm ilmi-keepalive
dsl operating-mode auto
!
interface FastEthernet1
duplex auto
speed auto
!
interface FastEthernet2
duplex auto
speed auto
!
interface FastEthernet3
duplex auto
speed auto
!
interface FastEthernet4
duplex auto
speed auto
!
ip http server
no ip http secure-server
!
!
!
control-plane
control-plane
!
!
line con 0
no modem enable
line aux 0
line vty 0 4
!
scheduler max-task-time 5000
end
I config my pc with 10.10.10.4 but I can?t connect to router.
How I get that the router ip be 10.10.10.1 and get config my router via http?
I don?t Know how configure it via commands.
Kind Regards
03-01-2007 06:27 AM
try below. replace X's with IP address for eth0. Use same IP range and subnet as assigned to your PC.
interface Ethernet0
description # Connected to you lan#
ip address XXX.XX.XX.X 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1348
hold-queue 100 out
no shut
03-01-2007 07:46 AM
how can I do it via command?
I do not know
Regards
03-01-2007 09:18 AM
Router>enable
Router#conf t
Router(config)#interface e0
Router(config-if)#ip address 10.10.10.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#exit
Router#copy run start
Type the commands as you see them and pay attention to the prompts. Im not a big fan of the gui, you might want to learn how to use the cli.
03-02-2007 04:28 AM
Dear ,
Thanks a lot for all, my router is up and working again.
Many thanks and Regards
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide