12-28-2014 10:35 AM - edited 03-05-2019 12:27 AM
Hi,
I have another problem - after upgrade ios wirelles connection not work.
After reload i have :
Configuration of subinterfaces and main interface
within the same bridge group is not permitted
STP: Unable to get the port parameters.
Please configure the bridge group on this interface first.
Please configure the bridge group on this interface first.
Please configure the bridge group on this interface first.
SETUP: new interface NVI0 placed in "shutdown" state
my old configuration work propertly in the old software, but after update i have notificatio.
Old thread:
https://supportforums.cisco.com/discussion/12379491/cisco-877w-no-wireless-connection
my current sh run:
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime
service password-encryption
!
hostname cisco
!
boot-start-marker
boot system flash:c870-advipservicesk9-mz.124-24.T6.bin
boot-end-marker
!
logging message-counter syslog
logging buffered 4096 informational
enable secret 5 $1$eCNp$rWuBfZ/cexnwnkm7L447s.
!
aaa new-model
!
!
!
!
aaa session-id common
!
!
dot11 syslog
!
dot11 ssid ciscowifi
vlan 1
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 050D031D26595D0617
!
dot11 wpa handshake timeout 500
ip source-route
!
!
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.56.1
!
ip dhcp pool CLIENT
import all
network 192.168.56.0 255.255.255.0
default-router 192.168.56.1
dns-server 8.8.8.8 194.204.159.1 194.204.152.34
lease 0 2
!
!
ip cef
no ip domain lookup
no ipv6 cef
!
multilink bundle-name authenticated
!
!
!
username marek password 7 00121A0908500A
!
!
!
archive
log config
hidekeys
!
!
ip tcp path-mtu-discovery
!
bridge irb
!
!
interface ATM0
description Polaczenie ADSL do ISP$ES_WAN$
no ip address
no atm ilmi-keepalive
pvc 0/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
hold-queue 224 in
!
interface FastEthernet0
description Edzia
!
interface FastEthernet1
description dom
!
interface FastEthernet2
description Dziadek
!
interface FastEthernet3
!
interface Dot11Radio0
no ip address
no ip redirects
ip local-proxy-arp
ip nat inside
ip virtual-reassembly
no dot11 extension aironet
!
encryption vlan 1 mode ciphers tkip
!
encryption mode ciphers aes-ccm tkip
!
broadcast-key change 3600
!
!
ssid ciscowifi
!
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
world-mode dot11d country AU indoor
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface Dot11Radio0.1
description ciscowifi
encapsulation dot1Q 1 native
no cdp enable
!
interface Vlan1
no ip address
bridge-group 1
!
interface Dialer0
description Interfejs dzwoniacy
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp chap hostname cos@neostrada.pl
ppp chap password 7 xxxxxxxxxxxxxxxxxxxxxx
!
interface BVI1
description Polaczenie dla sieci LAN
ip address 192.168.56.1 255.255.255.0
ip nat inside
ip virtual-reassembly
!
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
no ip http secure-server
!
!
ip nat inside source list 100 interface Dialer0 overload
ip nat inside source static tcp 192.168.56.10 80 interface Dialer0 80
ip nat inside source static tcp 192.168.56.10 22 interface Dialer0 22
!
logging trap debugging
logging 192.168.56.10
access-list 100 permit ip 192.168.56.0 0.0.0.255 any
access-list 100 deny ip any any
no cdp run
!
!
!
!
snmp-server community ciskacz RO
snmp-server chassis-id ciskacz
!
control-plane
!
bridge 1 protocol ieee
bridge 1 route ip
!
line con 0
no modem enable
line aux 0
line vty 0 4
exec-timeout 0 0
transport preferred ssh
transport input ssh
!
scheduler max-task-time 5000
end
please help - thanks!
01-05-2015 05:20 AM
Hello Marek,
I suppose you are not planning to do any kinds of advanced config using several VLANs and multiple SSIDs so let's just make your configuration simple and working.
In short, you need to remove all references to VLAN 1 and to any subinterfaces possibly related to the VLAN 1. This means in particular (follow these steps in sequence):
Best regards,
Peter
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide