12-27-2006 02:41 PM - edited 03-03-2019 03:11 PM
Hello!
I have a Cisco 827 that I it want to use for my connection to Internet in house.
I have tried several configurations but I have not managed to connect to Internet.
I don?t have static ip, my ip is dynamic.
This is my configuration:
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname gorka
!
enable secret xxx
enable password ++++++++!
ip subnet-zero
no ip routing
!
!
!
!
interface Ethernet0
ip address 192.168.1.1 255.255.255.0
no ip route-cache
bridge-group 1
hold-queue 100 out
!
interface ATM0
no ip address
no ip route-cache
no atm ilmi-keepalive
pvc 8/32
encapsulation aal5snap
!
dsl operating-mode auto
bridge-group 1
!
ip classless
ip http server
ip pim bidir-enable
!
!
!
snmp-server community public RO
bridge 1 protocol ieee
!
line con 0
stopbits 1
line vty 0 4
password ++++++++
login
!
scheduler max-task-time 5000
end
Do I need a dialer?
Thanks.
12-27-2006 09:14 PM
hi
You can refer the config samples stated in the below link for Cisco 827 routers.
http://www.cisco.com/en/US/products/hw/routers/ps380/prod_configuration_examples_list.html
regds
12-28-2006 03:11 PM
Hi,
Hope you don't mind if i jump in with some more specific info here.
It appears that you do not have dialer interface setup to negotiate ppp paramaters with you ISP.
Try the config below. you need to get the PVC settings from your ISP and the encapsulation type.
!
interface ATM0
no ip address
ip route-cache flow
no atm ilmi-keepalive
dsl operating-mode auto
no shut
!
interface ATM0.1 point-to-point
pvc 8/32
pppoe-client dial-pool-number 1
no shut
!
!
interface Dialer0
ip address negotiated
ip mtu 1452
ip nat outside
encapsulation ppp
dialer pool 1
ppp authentication chap callin
ppp chap hostname ISPUSERNAME
ppp chap password ISPPASSWORD
no shut
!
the ip address negotiated command will give the dialer interface an IP address from you ISP. to check it do a 'sh int dialer 0'.
Load this configuration into your router and watch in dialer 0 to see if it gets an ip address.
Let me know how this goes.
Remember - please rate all posts :)
Cheers
Stephen
12-28-2006 03:15 PM
Hi,
noticed this in your config:
no ip routing !!!
12-29-2006 12:35 AM
Hi,
Just noticed another thing thank to the last guy.
enable ip routing
create a static route point all traffic out dialer0
i.e. ip route 0.0.0.0 0.0.0.0 dialer0
also enable nat as follows
Int e0
ip nat inside
!
dialer 0
ip nat outside
!
ip nat inside source list 1 interface Dialer0 overload
!
access-list 1 permit 192.168.1.0 0.0.0.255
!
you need to do this to allow all PC's/hosts inside your router access to the internet.
Thanks... Pls Rate all posts
Stephen
12-31-2006 08:57 AM
Hi Stephen!
I am sorry not to have answered before, but I have not seen the response.
At the moment i have this configuration:
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
!
ip subnet-zero
!
vpdn enable
!
vpdn-group pppoe
request-dialin
protocol pppoe
!
interface Ethernet0
ip address 192.168.1.1 255.255.255.0
ip nat inside
hold-queue 100 out
!
interface ATM0
no ip address
no atm ilmi-keepalive
bundle-enable
dsl operating-mode auto
hold-queue 224 in
!
interface ATM0.1 point-to-point
pvc 8/32
pppoe-client dial-pool-number 1
!
interface Dialer1
ip address negotiated
ip mtu 1492
ip nat outside
encapsulation ppp
dialer pool 1
ppp chap hostname adslppp@telefonicanetpa
ppp chap password 0 adslppp
!
ip nat inside source list 1 interface Dialer1 overload
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
no ip http server
ip pim bidir-enable
!
!
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 1 deny any
!
line con 0
password indartsu99
stopbits 1
line vty 0
access-class 1 in
exec-timeout 120 0
password indartsu99
login
line vty 1 4
password indartsu99
login
!
scheduler max-task-time 5000
end
I have managed to go out to Internet but i can see only a few pages.
To the majority I do not go out.
If I remove the "acces list 1" I do not see any.
That interface affects? Do not I see any access-group in any interface?
Your mtu is different...
Can it be a safety problem?.
Doing a "show in eth0" I see that I have ip.
All interfaces are up.
I can do "ping" on the outside without problems from the pc and from the router.
Thanks.
Javier.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide