01-18-2006 09:06 AM - edited 03-03-2019 11:29 AM
Is there any way that I can get the serial number via CLI or SDM? I know that when you do a 'show version' you get the motherboard serial number, but I'm wondering if you can get the box serial number.
Solved! Go to Solution.
01-18-2006 09:26 AM
Hello,
unless the serial number has been somehow entered into the configuration (e.g. with the 'snmp-server chassis-id' command), there is TMBK no way to retrieve the number other than to read it off the box...
Regards,
GP
01-18-2006 09:26 AM
Hello,
unless the serial number has been somehow entered into the configuration (e.g. with the 'snmp-server chassis-id' command), there is TMBK no way to retrieve the number other than to read it off the box...
Regards,
GP
01-18-2006 10:02 AM
Hi,
On newer routers, the command "sh diag" displays the router Serial Number..
NOTE:- I am bit confused whether the command is sh diag or sh module, but I am 100% sure the command produces the desired result.
-Sai.
01-18-2006 05:36 PM
Hey,
I had been looking around as well and was only able to find link for Catalysts.
Also, if you are running a 720x, from the CLI you can issue show c7200 but I believe that may only show the NPE S/N.
Here are SNMP OIDs in order to retrieve serial numbers for Aironet access points.
Walk ENTITY-MIB::entPhysicalSerialNum (1.3.6.1.2.1.47.1.1.1.1.11),
there are several entries: chassis, radio, ...
Part of entPhysicalTable for AP1242AG
ENTITY-MIB::entPhysicalDescr.1 = "Cisco Aironet 1240 Series (IEEE 802.11a/g) Access Point"
ENTITY-MIB::entPhysicalDescr.2 = "802.11G Radio"
ENTITY-MIB::entPhysicalDescr.3 = "802.11A Radio"
ENTITY-MIB::entPhysicalDescr.4 = "PowerPCElvis Ethernet"
ENTITY-MIB::entPhysicalSerialNum.1 = "FCZXXXXXXXX"
ENTITY-MIB::entPhysicalSerialNum.2 = "GAMXXXXXXXX"
ENTITY-MIB::entPhysicalSerialNum.3 = "ALPXXXXXXXX"
ENTITY-MIB::entPhysicalSerialNum.4 = ""
ENTITY-MIB::entPhysicalModelName.1 = "AIR-AP1242AG-E-K9 "
ENTITY-MIB::entPhysicalModelName.2 = "Radio AIR-AP1242GR:5M80.13"
ENTITY-MIB::entPhysicalModelName.3 = "Radio AIR-AP1242A:5M80.13"
ENTITY-MIB::entPhysicalModelName.4 = ""
OIDs numerically (entPhysicalSerialNum only)
1.3.6.1.2.1.47.1.1.1.1.11.1 = "FCZXXXXXXXX"
1.3.6.1.2.1.47.1.1.1.1.11.2 = "GAMXXXXXXXX"
1.3.6.1.2.1.47.1.1.1.1.11.3 = "ALPXXXXXXXX"
1.3.6.1.2.1.47.1.1.1.1.11.4 = ""
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide