07-18-2012 10:37 PM - edited 03-04-2019 05:01 PM
On site 2 etherchannel is showing up but site 1 etherchannel is showing suspended
I am geeting flow control eeror
site2
47 Po47(RU) - Gi1/0/39(P) Gi2/0/39(P)
MUMBAISW1#show int gi1/0/39
GigabitEthernet1/0/39 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is e8b7.4812.a943 (bia e8b7.4812.a943)
Description: " p2p tata 10mbps"
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:36:38, output 00:00:03, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 11
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
1330462 packets input, 1732660399 bytes, 0 no buffer
Received 358 broadcasts (237 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 237 multicast, 0 pause input
0 input packets with dribble condition detected
891799 packets output, 117989357 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
MUMBAISW1#show int gi2/0/39
GigabitEthernet2/0/39 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is e8b7.4812.a945 (bia e8b7.4812.a945)
Description: " p2p airtel 10mbps"
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 26/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:03, output 00:00:32, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 10506000 bits/sec, 908 packets/sec
5 minute output rate 417000 bits/sec, 519 packets/sec
2878288 packets input, 3998920212 bytes, 0 no buffer
Received 93 broadcasts (88 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 88 multicast, 0 pause input
0 input packets with dribble condition detected
1792396 packets output, 204999828 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
------------------------------------------------------------------------------------------------------------------------------------------------------------------
Site1
77 Po77(RU) - Gi1/32(s) Gi2/32(P)
nihilent01#show int gi1/32
GigabitEthernet1/32 is up, line protocol is down (notconnect)
Hardware is C6k 1000Mb 802.3, address is 001e.f7e6.a180 (bia 001e.f7e6.a180)
Description: "tata point to point etherchannel"
MTU 1500 bytes, BW 100000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, media type is 10/100/1000BaseT
input flow-control is off, output flow-control is off
Clock mode is auto
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:37, output 00:42:58, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/1/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 1000 bits/sec, 2 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
L2 Switched: ucast: 12 pkt, 768 bytes - mcast: 45 pkt, 2880 bytes
L3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes mcast
L3 out Switched: ucast: 0 pkt, 0 bytes mcast: 0 pkt, 0 bytes
366592733 packets input, 64046114375 bytes, 0 no buffer
Received 71925 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
1 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
520052593 packets output, 646656050119 bytes, 0 underruns
3 output errors, 0 collisions, 8 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
nihilent01#show int gi2/32
GigabitEthernet2/32 is up, line protocol is up (connected)
Hardware is C6k 1000Mb 802.3, address is 001e.f7e6.a180 (bia 001e.f7e6.a180)
Description: "p2p airtel 10 Mbps"
MTU 1500 bytes, BW 100000 Kbit, DLY 10 usec,
reliability 255/255, txload 26/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, media type is 10/100/1000BaseT
input flow-control is off, output flow-control is on
Clock mode is auto
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:05, output 00:00:06, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 374000 bits/sec, 511 packets/sec
5 minute output rate 10506000 bits/sec, 906 packets/sec
L2 Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes
L3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes mcast
L3 out Switched: ucast: 0 pkt, 0 bytes mcast: 0 pkt, 0 bytes
1939787 packets input, 217667628 bytes, 0 no buffer
Received 8949 broadcasts (653 multicasts)
--More--
07-19-2012 03:40 AM
Hi all
Above flowcontrol issue is sorted.
But the issue we are not able to obtain redudancy
As there are two isp link.
When my one link goes down than the entire traffic is dropping
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide