Hello Everyone,
I 'm trying to set up a home lab with a couple of 28XX and 2651XM series routers.
I would like to simulate a frame-relay connection between HQ, Branch1 and Branch2 . All of them are conneced to a PSTN switch (2811 router) via T1 cross over cables. The connectivity is like this.
HQ
|
|
Branch 1 ---> PSTN-WAN <-- Branch 2
I have configured all the routers and FR switch with necessary configuration. However the link between HQ and Branch1 is not coming up. On both the routers I could see the line protocol is down.I have pasted the configuration below. Please advise if am missing anything here. (It is not a cable/port issue)
From the PSTN-WAN router
=======================================================
controller T1 0/0/0
framing esf
clock source internal
linecode b8zs
channel-group 0 timeslots 1-24
description ** SERIAL DATA CONNECTION TO HQ-RTR **
controller T1 0/1/0
framing esf
clock source internal
linecode b8zs
channel-group 0 timeslots 1-24
description ** SERIAL DATA CONNECTION TO BR1-RTR **
!
interface Serial0/0/0:0
description ** T1 DATA CONNECTION TO HQ-RTR **
no ip address
encapsulation frame-relay IETF
frame-relay lmi-type ansi
frame-relay intf-type dce
frame-relay route 201 interface Serial0/1/0:0 101
frame-relay route 202 interface Serial0/3/0:0 102
interface Serial0/1/0:0
description ** T1 DATA CONNECTION TO BR1-RTR **
no ip address
encapsulation frame-relay IETF
frame-relay lmi-type ansi
frame-relay intf-type dce
PSTN-WAN#sh ip int bri
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 10.10.100.2 YES NVRAM up up
FastEthernet0/1 192.168.0.11 YES NVRAM up up
Serial0/0/0:0 unassigned YES NVRAM up up
Serial0/0/1:0 unassigned YES unset down down
Serial0/0/1:1 unassigned YES unset down down
Serial0/0/1:2 unassigned YES unset down down
Serial0/0/1:22 unassigned YES unset down down
Serial0/0/1:23 unassigned YES NVRAM up up
Serial0/1/0:0 unassigned YES manual up down
Serial0/1/1:0 unassigned YES unset down down
Serial0/1/1:1 unassigned YES unset down down
Serial0/1/1:2 unassigned YES unset down down
Serial0/1/1:22 unassigned YES unset down down
Serial0/1/1:23 unassigned YES NVRAM up up
Serial0/3/0:0 unassigned YES NVRAM up up
Serial0/3/1:0 unassigned YES unset down down
Serial0/3/1:1 unassigned YES unset down down
Serial0/3/1:2 unassigned YES unset down down
Serial0/3/1:22 unassigned YES unset down down
Serial0/3/1:23 unassigned YES NVRAM up up
Loopback0 1.1.1.1 YES NVRAM up up
From the HQ router
====================================================================
controller T1 0/0/0
channel-group 0 timeslots 1-24
framing esf
clock source internal
linecode b8zs
interface Serial0/0/0:0
no ip address
encapsulation frame-relay
frame-relay lmi-type ansi
!
interface Serial0/0/0:0.1 point-to-point
ip address 10.10.111.1 255.255.255.0
ip ospf mtu-ignore
snmp trap link-status
frame-relay interface-dlci 201
!
interface Serial0/0/0:0.2 point-to-point
ip address 10.10.112.1 255.255.255.0
ip ospf mtu-ignore
snmp trap link-status
frame-relay interface-dlci 202
From the BR1 router
========================================
controller T1 1/0
channel-group 0 timeslots 1-24
framing esf
clock source internal
linecode b8zs
!
interface Serial 1/0:0
no ip address
encapsulation frame-relay IETF
fair-queue
frame-relay lmi-type ansi
!
interface Serial 1/0:0.1 point-to-point
ip address 10.10.111.2 255.255.255.0
ip ospf mtu-ignore
snmp trap link-status
frame-relay interface-dlci 101
!
========================================================
