09-16-2012 08:23 AM - edited 03-04-2019 05:34 PM
I need change redandunt mode SSO to redandunt mode none ,and upgrade IOS XE ,I correct ?
1. I upload new IOS-XE and check boot system bootflash:/NewIOS (I will must upgrade rommon ?)
2. I change configuration "redandunt mode sso to redandunt mode none" after I will copy run start (I correct ? or any concern such as show platfrom, show version, dir ect, )
3. I can be reload for ASR take newios redandunt mode none.
I correct all ?
Thank you for respones.
Sittichai T.
Solved! Go to Solution.
09-16-2012 10:04 AM
Hi Sittichai,
Could you explain in more details on why do you want to change redunancy mode to none? Do you use IOS process redundancy on it?
Also, please post "show platform" command output here.
Generally, if you do not care about service impact due to the router reload, on any ASR router you can change the boot string to point to new image, save configuration and reload the router.
For less service impact, you should use ISSU procedure, which you can see in the following guide:
http://www.cisco.com/en/US/docs/routers/asr1000/configuration/guide/chassis/issu.html#wp1218296
Kind Regards,
Ivan Shirshin
**Please grade this post if you find it useful.
09-18-2012 12:27 AM
Hi,
If you want to change to single process, config the following:
Router# configure terminal
Router(config)# redundancy
Router(config-red)# mode none
Router(config-red)# end
Router#
There is no need to run "issu runversion". Since you are doing service impacting upgrade with router reload, you just need to change the boot string and reload:
Router#show run | i boot //find the current boot string, e.g. "boot system bootflash:/IOS-XE/packages.conf"
Router# configure terminal
//remove the old boot string now, using the output you got above, e.g.:
Router(config)# no boot system bootflash:/IOS-XE/packages.conf
//add new boot string, specify correct path
Router(config)# boot system bootflash:/IOS-XE/asr1000rp1-advipservicesk9.03.04.03.S.151-3.S3.bin
//save config
wr
//reload to load new image
reload
Note that this is service impacting upgrade!
You can also use ISSU packages upgrade procedure but that requires 2 IOS processes to be configured:
http://www.cisco.com/en/US/docs/routers/asr1000/configuration/guide/chassis/issu.html#wp1162196
Kind Regards,
Ivan Shirshin
**Please grade this post if you find it useful.
09-16-2012 10:04 AM
Hi Sittichai,
Could you explain in more details on why do you want to change redunancy mode to none? Do you use IOS process redundancy on it?
Also, please post "show platform" command output here.
Generally, if you do not care about service impact due to the router reload, on any ASR router you can change the boot string to point to new image, save configuration and reload the router.
For less service impact, you should use ISSU procedure, which you can see in the following guide:
http://www.cisco.com/en/US/docs/routers/asr1000/configuration/guide/chassis/issu.html#wp1218296
Kind Regards,
Ivan Shirshin
**Please grade this post if you find it useful.
09-17-2012 08:28 PM
current I used ASR1002 1 unit version Version 12.2(33)XNF2 IOS-XE :asr1000rp1-advipservicesk9.02.06.01.122-33.XNF1.bin
and redundancy mode sso
but, I need to single process , I can be upgrade asr1000rp1-advipservicesk9.03.04.03.S.151-3.S3.bin in ASR1002 ?
and I refer by command issu runningversion and result
ASR#issu runversion
--- Starting local lock acquisition on R0 ---
Finished local lock acquisition on R0
FAILED: Operation runversion cannot be performed: no install in progress
I just need redundancy mode none and upgrade IOS-XE from 12.33 to 15.1-3
PS. now :bootflash:/IOS-XE/packages.conf ,
I will change bootflash:/IOS-XE/asr1000rp1-advipservicesk9.03.04.03.S.151-3.S3.bin and change redundancy mode none and reload for take router ---- but I don't sure after tranfrom 12.33 to 15.1
please make sure to me.
Thank you,
Sittichai Taykum
09-18-2012 12:27 AM
Hi,
If you want to change to single process, config the following:
Router# configure terminal
Router(config)# redundancy
Router(config-red)# mode none
Router(config-red)# end
Router#
There is no need to run "issu runversion". Since you are doing service impacting upgrade with router reload, you just need to change the boot string and reload:
Router#show run | i boot //find the current boot string, e.g. "boot system bootflash:/IOS-XE/packages.conf"
Router# configure terminal
//remove the old boot string now, using the output you got above, e.g.:
Router(config)# no boot system bootflash:/IOS-XE/packages.conf
//add new boot string, specify correct path
Router(config)# boot system bootflash:/IOS-XE/asr1000rp1-advipservicesk9.03.04.03.S.151-3.S3.bin
//save config
wr
//reload to load new image
reload
Note that this is service impacting upgrade!
You can also use ISSU packages upgrade procedure but that requires 2 IOS processes to be configured:
http://www.cisco.com/en/US/docs/routers/asr1000/configuration/guide/chassis/issu.html#wp1162196
Kind Regards,
Ivan Shirshin
**Please grade this post if you find it useful.
09-26-2012 08:40 PM
Thank you for information Ivan,
I was try follow you,
after reboot ASR can used single processer but, when I show redundancy configure still mode sso
I used in config t and redundancy and default-exit and enter and save non reboot after then show config again config in redundacy mode none
thank you very much ...!!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide