03-25-2012 03:09 AM - edited 03-04-2019 03:47 PM
Dear,
I have two ISPs, one is sending me the full BGP router ( ISP-A) while the other one is sending me only the default reoute 0.0.0.0 (ISP-B).
How I can manage and do load balancing to both ISPs?
regards
MHS
03-25-2012 03:39 AM
Hi,
Impossible. If You have only default route from provider B, all traffic will go to existing routes, except illegal traffic without destination. For example, port scanning.
BGP isn't for load balancing, it's for traffic management. You'll need to plan what traffic destination to be sent to which provider. If no, then one provider will be better to almost all the world.
Anyway, You'll need to ask second provider for real routes. It can be full table, or something smaller. For example, Your country inside routes from direct peers between local providers. And also You'll need to ask provider to announce Your routes to these links too. Some providers give possibilities to control outgoing routes through route tags, You can ask provider for it. Some routing paths can be assimetric, but mostly it's better to keep it simetric. Anyway, it will be nat a real balancing.
No one will give You universal recipe for traffic and route management. It's individual an depends from Your providers, Your need, Your possibilities, Your wishes.
Kind Regards,
UgisD.
03-25-2012 05:38 AM
Hi, Have a look at the following BGP configuration guide for load sharing:
http://www.cisco.com/en/US/tech/tk365/technologies_configuration_example09186a00800945bf.shtml
It states that:
"Load balancing is not possible in a multihomed environment with two ISPs. BGP selects only the single best path to a destination among the BGP paths that are learned from different AS's, which makes load balancing impossible. But, load sharing is possible in such multihomed BGP networks"
03-25-2012 05:52 AM
Thanks UgisD & Sean,
However, currently most of my traffic 95 % is going through the ISP-A which advertise the full BGP routing and very less traffic through the ISP-B which advertise the defautl route.
Is it there a way to manage the traffic to both ISPs in such away? or I have to ask one ISP-B to send the full BGP routes or ISP-A to send the defualt route only.
Which is better for traffic managment to have two defualt routes or the full BGP routes?
regards
MHS
03-25-2012 07:41 AM
Got to the same issue.
The following options were implemented:
1.) ISP-b run full routing (best if it's 1st tier ISP)
2.) ISP-b should get you a new /24 block and advertise it on both providers
3.) start using the ISP-b IP block for web services
It did help the traffic but not much. ISP-b just a third tier ISP and not so many customers.
03-25-2012 11:47 PM
Dear Eli,
Could you pelase clarify point (2 & 3).
2- I have my own subnet /20 I am advertiving the full subnet /20 to both ISP and also hlaf subnet to ISP-A and another half to ISP-B.
3- Can you clarifiy it more.
Thnx
MHS
03-25-2012 12:15 PM
Hi Alshamlan,
If there is not any special reason to get the full internet routing table by your ISP, to request them to send you a default route.
It will be much easier to troubleshoot, to load share and you will save much CPU and Memory from your routers.
Hope that helps,
Vasilis
03-25-2012 11:50 PM
Dear Vasillis,
Do you mean It is easier for me to ask both ISP to send the default route?
reg
MHS
03-26-2012 12:02 AM
Hi Alshamlan,
Yes, if you do not need the full routing table to your routes for any special reason, I would recommend to receive just a default route for the reason described to my previous post.
Regards,
Vasilis
03-26-2012 12:16 AM
Hi Vasillis,
Thanks for your reply. Do you have documents which shows how we can manage the full BGP routing in compare to the managing the default route?
regards
03-26-2012 02:04 AM
Hi,
If You want more simple construction, You can ask both providers to announce only their own networks, or same far and stable network. Then You can use two static default routes to these networks.Static routes allow two paralel destinations.
For incoming trafic You can use Your existing solution with /20 to both and /21 or smaller for each.
More complex sollution is to filter routes with route-maps and send community tags to providers, if they accept them.
03-26-2012 02:54 AM
Hi Alshamlan,
No, i do not have any document related to internet routing table management....i have only my experience which I shared with you
03-26-2012 09:47 AM
Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
If your platform supports it, see if OER/PfR might work for you.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide