cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1172
Views
0
Helpful
2
Replies

Multicast -- Multicast VPN --- XRv

Would like your assistance please regarding below quesitos

 

1- As you know to verify multicast we can use ping.

My problem is that when you ping using source loopback address it does not work [spare-mode is configured normally under loopback] however when you configure using outgoing interface it pings normally

What could be the reason for this ?

 

2- Does XRv simulator works fine with multicast. I am having very strange behavior is that OIL list is always null although source is directly connected. Not sure if its a bug or XRv issue

 

R8#ping 227.7.7.7 repeat 10

 

Type escape sequence to abort.

Sending 10, 100-byte ICMP Echos to 227.7.7.7, timeout is 2 seconds:

..........

R8#

 

RP/0/0/CPU0:XR2#show pim topology

Thu May 22 06:14:34.625 UTC

 

IP PIM Multicast Topology Table

Entry state: (*/S,G)[RPT/SPT] Protocol Uptime Info

Entry flags: KAT - Keep Alive Timer, AA - Assume Alive, PA - Probe Alive

    RA - Really Alive, IA - Inherit Alive, LH - Last Hop

    DSS - Don't Signal Sources,  RR - Register Received

    SR - Sending Registers, SNR - Sending Null Registers

    E - MSDP External, EX - Extranet

    MFA - Mofrr Active, MFP - Mofrr Primary, MFB - Mofrr Backup

    DCC - Don't Check Connected, ME - MDT Encap, MD - MDT Decap

    MT - Crossed Data MDT threshold, MA - Data MDT Assigned

    SAJ - BGP Source Active Joined, SAR - BGP Source Active Received,

    SAS - BGP Source Active Sent, IM - Inband mLDP

Interface state: Name, Uptime, Fwd, Info

Interface flags: LI - Local Interest, LD - Local Dissinterest,

    II - Internal Interest, ID - Internal Dissinterest,

    LH - Last Hop, AS - Assert, AB - Admin Boundary, EX - Extranet,

    BGP - BGP C-Multicast Join, BP - BGP Source Active Prune,

    MVS - MVPN Safi Learned, MV6S - MVPN IPv6 Safi Learned

 

(*,224.0.1.40) DM Up: 00:56:21 RP: 0.0.0.0

JP: Null(never) RPF: Null,0.0.0.0 Flags: LH DSS

  Loopback0                   00:56:21  off LI II LH

  GigabitEthernet0/0/0/2      00:56:14  off LI LH

 

(*,227.7.7.7) SM Up: 00:29:15 RP: 20.20.20.20*

JP: Join(never) RPF: Decapstunnel3,20.20.20.20 Flags:

  GigabitEthernet0/0/0/2      00:29:15  fwd Join(00:03:13)   <<--- receiver sends PIM Join normally

 

(10.8.20.8,227.7.7.7)SPT SM Up: 00:00:03

JP: Join(00:00:46) RPF: GigabitEthernet0/0/0/0.820,10.8.20.8* Flags: KAT(00:03:29) RA RR (00:04:33)

  No interfaces in immediate olist   <<<<<------

 

Appreciate your assistance

Regards

Sherif Ismail

2 Replies 2

Cuong Nguyen
Level 1
Level 1

Hi Sherif Ismail,

I encountered this and checked around. It seems that XRv supports Control-Plane features fully - BGP/IGP/LDP/PIM/etc. will work. However, Data-plane is supported with limitations.

 

Cheers,

Cuong.

Hello,

I just installed XRv 5.2.0. Shall I expect MVPN data plane work?

Thanks,

Ato