need help with. high school networking assignment

[Michaelpro08]

i need to make a three router network that can ping to eachother. i have the first two networks working. but the third gives a error "destination host unreachable" any help will be appreciated

here is the router setup :https://ufile.io/chn0ij3n

here is the instructions from the teacher, should help you understand how i made it: https://docs.google.com/document/d/1i4I6Ie8M3aiROvydE0vFTo28f6AxTmw7EQJEgA3KR8Q/edit?usp=sharing

[balaji.bandi]

destination host unreachable  = this means the next hop or end device do not know how to reach the destination.

traceroute helps you, where it stops, that is the device you need to investigate the routing.

Rather instruction manual,. you need to provide the configuration you have done on your lab

post below information from all devices :

show run

show IP route

show IP interface brief

[Michaelpro08]

show run

router 0=. 

ip dhcp pool america

network 192.168.1.0 255.255.255.0

default-router 192.168.1.1

!

!

!

ip cef

router 1 =

ip dhcp pool asia

network 192.168.2.0 255.255.255.0

default-router 192.168.2.1

!

!

!

ip cef

router 2= 

ip dhcp pool europe

network 192.168.39.0 255.255.255.0

default-router 192.168.39.1

!

!

!

no ip cef

show ip route

router 0=

Gateway of last resort is not set

10.0.0.0/24 is subnetted, 1 subnets

C 10.0.0.0 is directly connected, Serial2/0

C 192.168.1.0/24 is directly connected, FastEthernet0/0

O 192.168.2.0/24 [110/65] via 10.0.0.2, 00:15:32, Serial2/0

router 1=

10.0.0.0/24 is subnetted, 2 subnets

C 10.0.0.0 is directly connected, Serial2/0

C 10.0.1.0 is directly connected, Serial3/0

O 192.168.1.0/24 [110/65] via 10.0.0.1, 00:17:09, Serial2/0

C 192.168.2.0/24 is directly connected, FastEthernet0/0

router 2= 

10.0.0.0/24 is subnetted, 1 subnets

C 10.0.0.0 is directly connected, Serial3/0

C 192.168.39.0/24 is directly connected, FastEthernet0/0

show ip interface brief

router 0= 

FastEthernet0/0 192.168.1.1 YES manual up up

FastEthernet1/0 unassigned YES unset administratively down down

Serial2/0 10.0.0.1 YES manual up up

Serial3/0 unassigned YES unset administratively down down

FastEthernet4/0 unassigned YES unset administratively down down

FastEthernet5/0 unassigned YES unset administratively down down

router 1=

Interface IP-Address OK? Method Status Protocol

FastEthernet0/0 192.168.2.1 YES manual up up

FastEthernet1/0 unassigned YES unset administratively down down

Serial2/0 10.0.0.2 YES manual up up

Serial3/0 10.0.1.2 YES manual up up

FastEthernet4/0 unassigned YES unset administratively down down

FastEthernet5/0 unassigned YES unset administratively down down

Router2=

Interface IP-Address OK? Method Status Protocol

FastEthernet0/0 192.168.2.1 YES manual up up

FastEthernet1/0 unassigned YES unset administratively down down

Serial2/0 10.0.0.2 YES manual up up

Serial3/0 10.0.1.2 YES manual up up

FastEthernet4/0 unassigned YES unset administratively down down

FastEthernet5/0 unassigned YES unset administratively down down

hope this helps. if there is any more information you need. let me know

[balaji.bandi]

as i see your config Router 1 and Router 2 have same IP address on the interface, which conflicts in the network

change to un used IP address and test it.

[Michaelpro08]

When you say “have the same ip address on the interface. Do you mean serial interface or the network such as. 

ip dhcp pool asia

network 192.168.2.0 255.255.255.0

i have changed the serial ports already so now each serial port has a different ip

Please specify where the ip address needs to be changed 

[balaji.bandi]

router 1=

FastEthernet0/0 192.168.2.1 YES manual up up

Serial2/0 10.0.0.2 YES manual up up

Serial3/0 10.0.1.2 YES manual up up

Router2=

Interface IP-Address OK? Method Status Protocol

FastEthernet0/0 192.168.2.1 YES manual up up

Serial2/0 10.0.0.2 YES manual up up

Serial3/0 10.0.1.2 YES manual up up

If you have changed this above post new config as below

show run

show IP interface brief

show cdp neigh

show IP arp