08-28-2020 05:27 AM
Hello all,
replaced a 2900 router with a new 4331 isr. Worked great for 5 days and then Became increasingly unresponsive. Reset to factory and started from scratch again and it works (local network works great) seeing some packet loss pinging external ip from an external network and it’s very slow loading web pages, I currently have the trial boost license. I have gotten the notice that I was approaching the license cap one time. Negotiation is set to auto.
any ideas what would be causing such slow speeds
08-28-2020 07:32 AM
sh license
Index 1 Feature: appxk9
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Active, Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
Index 2 Feature: uck9
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Active, Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
Index 3 Feature: securityk9
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Active, Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
Index 4 Feature: ipbasek9
Period left: Life time
License Type: Permanent
License State: Active, In Use
License Count: Non-Counted
License Priority: Medium
Index 5 Feature: FoundationSuiteK9
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Active, Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
Index 6 Feature: AdvUCSuiteK9
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Active, Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
Index 7 Feature: cme-srst
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Active, Not in Use, EULA not accepted
License Count: 0/0 (In-use/Violation)
License Priority: None
Index 8 Feature: hseck9
Index 9 Feature: throughput
Period left: 7 weeks 4 days
Period Used: 6 days 19 hours
License Type: EvalRightToUse
License State: Active, In Use
License Count: Non-Counted
License Priority: Low
Index 10 Feature: internal_service
08-28-2020 07:33 AM
should i upgrade the ios xe software?
08-28-2020 08:48 AM
Here is my LAN sh inter
GigabitEthernet0/0/1 is up, line protocol is up
Hardware is ISR4331-3x1GE, address is 3c13.cccc.c351 (bia 3c13.cccc.c351)
Internet address is X.X.X.X/23
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 2/255, rxload 65/255
Encapsulation ARPA, loopback not set
Keepalive not supported
Full Duplex, 1000Mbps, link type is auto, media type is RJ45
output flow-control is off, input flow-control is off
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/375/0/0 (size/max/drops/flushes); Total output drops: 57305
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 257319000 bits/sec, 31292 packets/sec
5 minute output rate 8508000 bits/sec, 11136 packets/sec
1849991537 packets input, 1883417327760 bytes, 0 no buffer
Received 80916 broadcasts (0 IP multicasts)
40802 runts, 0 giants, 0 throttles
646549 input errors, 646549 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 73977 multicast, 0 pause input
648020027 packets output, 101963949439 bytes, 0 underruns
0 output errors, 0 collisions, 5 interface resets
1620 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
5 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
08-28-2020 07:47 PM
Full Duplex, 1000Mbps, link type is auto, media type is RJ45 646549 input errors, 646549 CRC, 0 frame, 0 overrun, 0 ignored
Potential speed/duplex mismatch error.
This is a copper port. The port configuration should be auto speed/auto duplex.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide