ā11-29-2016 01:51 AM - edited ā03-05-2019 07:34 AM
Hi,
Please find the below ouput frow the show interface command from the Router Outside Interface connected to Internet Service Provider.
0 watchdog, 0 multicast, 122 pause input
1474107 packets output, 352324562 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 220198 pause output
Is this a cause of concern ? I have GRE Tunnel running over this Internet interface, passing Voice traffic as well. Please advice.
Thanks & Regards
Sreeraj
ā11-29-2016 10:36 AM
Sreeraj
No two devices in a network path are matching each other. In other words, there will be mismatches. Given this, you can expect some amount of pause frames. Pause frames are basically layer-2 flow control mechanism, indicating congestion.
Partial outputs will lead to speculation. Speculations are generally not helpful. Please consider sharing the complete output (show tech preferably).
Kind regards ... Palani
ā11-30-2016 01:46 AM
ā11-30-2016 06:21 AM
Hi Sreeraj
The router is underpowered to handle the load. Take a look at your CPU history. You are reaching high 90s, consistently and repeatedly.
The time/date when show tech was taken is not the busiest time and so, I am not getting a clean picture on the utilization.
Take a look at http://miercom.com/pdf/reports/20091001.pdf
While this does not cover 2921 itself, we know that 2921 is positioned between 2911 and 2951. So, you can expect a t'put around 35-60Mbps, depending on the pktSize. If your contracted WAN bandwidth is higher than this, then please consider upgrading the routing platform that is designed to meet the contracted WAN bandwidth.
Kind regards ... Palani
ā11-30-2016 09:58 PM
ā12-01-2016 06:13 AM
Hi Sreeraj
As you may have noticed, CPU was NOT high when the show tech was taken.
Recommend the following changes be made:
! process cpu threshold type total rising 90 interval 10 falling 60 interval 10 process cpu threshold type interrupt rising 60 interval 10 falling 40 interval 10 process cpu threshold type process rising 75 interval 10 falling 60 interval 10 !
line con 0
exec prompt timestamp
!
line vty 0 4
exec prompt timestamp
!
int gi 0/0
ip flow ingress
!
int gi 0/1
ip flow ingress
!
int tun 0
ip flow ingress
!
logging buffer 1000000
!
These cmds trigger a syslog when the CPU rises and falls. The syslog message sample would look something like:
%SYS-1-CPURISINGTHRESHOLD: Threshold: Total CPU Utilization(Total/Intr): 90%/85%, Top 3 processes(Pid/Util): 61/2%, 125/1%, 2/0%
From this message, we can be informed about:
Total CPU utilization
Amount of CPU spent servicing interrupts
Top 3 processes PID# with # CPU utilized by these processes
How long the condition lasted
Most important: Are you actively troubleshooting any performance issues? Are any of your users complaining slow performance? What is the contracted bandwidth with your WAN provider?
Wait for 1 business week to complete. Then, share the show log. This will tell us a pattern of when the CPU load is high. Based on what we find here, we can make progress.
Kind regards ... Palani
ā12-01-2016 09:44 PM
Sure, I will share the log.
At the moment, is the PAUSE INPUT and PAUSE OUTPUT a cause of concern ?
Please suggest.
ā12-02-2016 05:56 AM
Hi Sreeraj
Yes, it is definitely a cause for concern. That is the reason for recommending you to continue investigation.
Please don't clear counters. Just issue show cmd twice and look at the delta if you want to know how quickly the counters are changing.
Kind regards .... Palani
ā12-12-2016 12:30 AM
ā12-12-2016 11:00 PM
Hi Palani, Hope you have got a chance to look at the "show tech" shared.
Also, the Internet Leased Line bandwidth delivered by Service provider is 10 Mbps.
Kindly check and suggest.
ā12-14-2016 07:28 AM
Hi Sreeraj
Unfortunately, the show tech was taken when the CPU was normal:-( Assuming you made the config changes mentioned earlier, please send us show log. Let's see what it tells us.
Kind regards .... Palani
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide