PPPOE configuration for Cisco 851and cisco 870 router

[krishan.saran]

Hi Guys

I have two cisco 850 and 870 series routers i tryed alot but i am unable to configure PPOE on both of the routers there is no PPPOE enable command available I tryed VPDN s too but no luck any body have some clue

[vragotha]

Hi,

     Here is a link to the configuration guide -

http://www.cisco.com/en/US/docs/routers/access/800/850/software/configuration/guide/pppoenat.html

If you are still having trouble, can you post what kind of errors you get when you try to enter the configuration commands?

[krishan.saran]

Hi

I already tried these steps but at step 4 where i enter the protocol command there is no PPPoE option just only l2tp option is there

	Command or Action	Purpose
Step 1	vpdn enable Example: Router(config)# vpdn enable Router(config)#	Enables VPDN on the router.
Step 2	vpdn-group name Example: Router(config)# vpdn-group 1 Router(config-vpdn)#	Creates and associates a VPDN group with a customer or VPDN profile.
Step 3	request-dialin Example: Router(config-vpdn)# request-dialin Router(config-vpdn-req-in)#	Creates a request-dialin VPDN subgroup, indicating the dialing direction, and initiates the tunnel.
Step 4	protocol {l2tp | pppoe} Example: Router(config-vpdn-req-in)# protocol pppoe Router(config-vpdn-req-in)#	Specifies the type of sessions the VPDN subgroup can establish.
Step 5	exit Example: Router(config-vpdn-req-in)# exit Router(config-vpdn)#	Exits request-dialin VPDN group configuration.
Step 6	exit Example: Router(config-vpdn)# exit Router(config)#	Exits VPDN configuration, returning to global configuration mode.

[vragotha]

Can you post a 'show ver' and 'show run' ?

[krishan.saran]

Hi  Thanks for your help

Here is the Show Version

office(config-vpdn-req-in)#do sho ver

Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T13, RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2010 by Cisco Systems, Inc.

Compiled Wed 07-Apr-10 20:49 by prod_rel_team

ROM: System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARE

office uptime is 8 hours, 12 minutes

System returned to ROM by reload

System restarted at 15:41:12 PCTime Sat Aug 7 2010

System image file is "flash:c850-advsecurityk9-mz.124-15.T13.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco 851 (MPC8272) processor (revision 0x300) with 59392K/6144K bytes of memory.

Processor board ID FHK1426601C

MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10

5 FastEthernet interfaces

128K bytes of non-volatile configuration memory.

20480K bytes of processor board System flash (Intel Strataflash)

Configuration register is 0x2102

Here is the command i was entrenig

office#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

office(config)#vpdn en

office(config)#vpdn enable

office(config)#vpdn-gro

office(config)#vpdn-group 1

office(config-vpdn)#requ

office(config-vpdn)#request-dialin

office(config-vpdn-req-in)#pro

office(config-vpdn-req-in)#protocol pp

office(config-vpdn-req-in)#protocol ?

  l2tp  Use L2TP

There is no protocol PPPoE

thans what i was doing

[Giuseppe Larosa]

Hello Krishan,

your router is running 12.4(15)T you don't need anymore vpdn to enable pppoe client on it

see

http://www.cisco.com/en/US/docs/ios/bbdsl/configuration/guide/bba_ppoe_client_ps6441_TSD_Products_Configuration_Guide_Chapter.html#wp1070857

there is a section for newer releases

Configuring a PPPoE Client on an Ethernet Interface

Perform this task to configure a PPPoE client on an Ethernet interface.

SUMMARY STEPS

1. enable

2. configure terminal

3. interface ethernet number

4. pppoe-client dial-pool-number number

Hope to help

Giuseppe

[krishan.saran]

Hi

Any body can post the the running configuration on  12.4(15)T IOS with PPPoE configuration complete

I will be rely thankful i don't have much experience of CLI i normally configure through SDM but through SDM i am getting this PPPoE enable error. but if i have the running configuration than i can program, because i have to drive 3hour for that site and i don't want to stuck there Please Please

[kmccourt]

http://www.dslreports.com/forum/r19183186-Config-Cisco-851-PPPoE-DSL

This link might help you.