12-05-2023 05:51 AM
hello guys,
I hope you're well.
I've set up VRRP on two C9500s, it works but I have a random problem accessing the second C9500, sometimes it's accessible, sometimes it's not.
Regards.
Solved! Go to Solution.
12-06-2023 07:04 AM
12-05-2023 05:57 AM
Access use real interface IP not VIP.
Try this and check
MHM
12-06-2023
06:14 AM
- last edited on
01-02-2024
12:55 AM
by
Translator
Hello MHM,
Thank you for your return.
For management I use the vla x interface, which is the default gateway and also the virtual interface for VRRP
So you're suggesting I create another vlan dedicated to MGMT? or use the chassis outofband?
SW01 :
interface Vlan X
description VLAN_ADMIN
ip address 192.168.1.1 255.255.255.0 ---- used for MGMT
vrrp 1 address-family ipv4
description VRRP group
priority 120
preempt delay minimum 60
address 192.168.1.1 primary
SW02:
interface Vlan X
description VLAN_ADMIN
ip address 192.168.1.2 255.255.255.0 ---- used for MGMT
vrrp 1 address-family ipv4
description VRRP group
priority 120
preempt delay minimum 60
address 192.168.1.1 primary
Regards.
12-06-2023 06:36 AM
Yes use vlan SVI detect for mgmt.
MHM
12-06-2023 07:02 AM
that's what I use the SVI interface, but it's in the VRRP.
Should I create a new SVI and not add it to VRRP to use it as MGMT ?
Regards.
12-06-2023 07:04 AM
Yes svi config without vrrp
MHM
12-06-2023 07:05 AM
OK bro I try and back to you.
Thx again.
Regards.
12-05-2023 05:57 AM
You need to provide some information, what IOS XE code running on both Cat 9500 ?how is this Cat 9500 connected each other (Hope they are not in SVL right ?)
show vrrp config of both the devices
tell us from what IP address not reachable from what source IP address ?
12-06-2023
06:30 AM
- last edited on
01-02-2024
01:00 AM
by
Translator
Hello Balaji,
Thank you for your return.
1 - IOSXE = Version 17.03.05
2 - No SVL but VRRP
3 - The two devices are connected directly with two 40Gigabyte links
4 - Show Vrrp SW01
show vrrp brief
Interface Grp A-F Pri Time Own Pre State Master addr/Group addr
VlX 1 IPv4 255 0 Y Y MASTER X.X.X.X(local) X.X.X.X
VlX 1 IPv4 255 0 Y Y MASTER X.X.X.X(local) X.X.X.X
VlXX 1 IPv4 255 0 Y Y MASTER X.X.X.X(local) X.X.X.X
VlXX 1 IPv4 255 0 Y Y MASTER X.X.X.X(local) X.X.X.X
VlXX 1 IPv4 255 0 Y Y MASTER X.X.X.X(local) X.X.X.X
VlXX 1 IPv4 255 0 Y Y MASTER X.X.X.X(local) X.X.X.X
VlXX 1 IPv4 255 0 Y Y MASTER X.X.X.X(local) X.X.X.X
VlXX 1 IPv4 255 0 Y Y MASTER X.X.X.X(local) X.X.X.X
VlXX 1 IPv4 255 0 Y Y MASTER X.X.X.X(local) X.X.X.X
VlXX 1 IPv4 255 0 Y Y MASTER X.X.X.X(local) X.X.X.X
VlXXX 1 IPv4 255 0 Y Y MASTER X.X.X.X(local) X.X.X.X
VlXXX 1 IPv4 255 0 Y Y MASTER X.X.X.X(local) X.X.X.X
VlXXX 1 IPv4 255 0 Y Y MASTER X.X.X.X(local) X.X.X.X
VlXXX 1 IPv4 255 0 Y Y MASTER X.X.X.X(local) X.X.X.X
4 - Show Vrrp SW02 (Not reachable)
5 - From LAN users (Another VLAN), but the address is sometimes reachable and sometimes not
Regards.
12-06-2023 07:29 AM
can you try ping 192.168.1.2 and try to connect.
how is these switches connected each other what port, where is your STP root bridge for the VLAN ?
where is users connectd ?
12-06-2023 07:55 AM - edited 12-28-2023 03:47 AM
When I try to ping it's not reachable and also when I connect with SSH (Random)
The inter-connection is made
STP is activated on SW01 (vlan 1-4094) root primary
on SW02 (vlan 1-4094) root secondary
Users are connected on access switches which terminates either on another access switch or on the last acces switch connected to VRRP switch depending on the location.
Regards.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide