QOS on 7600 ethernet interface

[Muhammed AKYUZ]

Hi,

I am trying to apply qos on ethernet interfece but i am getting an error.

BACKBONE_ROUTER_7609(config)#int g 3/5

BACKBONE_ROUTER_7609(config-if)# service-policy output QOS

priority command is not supported in output direction for this interface

Configuration failed on:

GigabitEthernet3/5

i can apply same qos to serial interfaces.

BACKBONE_ROUTER_7609#sh module

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  1    0  4-subslot SPA Interface Processor-200  7600-SIP-200       JAE1043DXSS

  2    0  4-subslot SPA Interface Processor-200  7600-SIP-200       JAE1046F04M

  3   48  SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX     SAL10414H5J

  4    0  2 port adapter Enhanced FlexWAN        WS-X6582-2PA       JAE1044EDNH

  5    2  Supervisor Engine 720 (Active)         WS-SUP720-3B       SAL103931LS

  6    2  Supervisor Engine 720 (Hot)            WS-SUP720-3B       SAL103933TY

  8    0  2 port adapter Enhanced FlexWAN        WS-X6582-2PA       JAE14380BB4

Mod MAC addresses                       Hw    Fw           Sw           Status

--- ---------------------------------- ------ ------------ ------------ -------

  1  0019.e842.4ac0 to 0019.e842.4aff   1.3   12.2(18)SXF7 12.2(18)SXF7 Ok

  2  0019.0656.a380 to 0019.0656.a3bf   1.3   12.2(18)SXF7 12.2(18)SXF7 Ok

  3  0018.b9e7.e220 to 0018.b9e7.e24f  11.1   7.2(1)       8.5(0.46)RFW Ok

  4  0019.56f3.c640 to 0019.56f3.c67f   2.3   12.2(18)SXF7 12.2(18)SXF7 Ok

  5  0017.9441.cc60 to 0017.9441.cc63   5.2   8.4(2)       12.2(18)SXF7 Ok

  6  0017.9441.cd2c to 0017.9441.cd2f   5.2   8.4(2)       12.2(18)SXF7 Ok

  8  1cdf.0f4b.f440 to 1cdf.0f4b.f47f   2.6   12.2(18)SXF7 12.2(18)SXF7 Ok

Mod  Sub-Module                  Model              Serial       Hw     Status

---- --------------------------- ------------------ ----------- ------- -------

1/0 8xCHT1/E1 SPA               SPA-8XCHT1/E1      JAB104504NM  1.5    Ok

1/1 8xCHT1/E1 SPA               SPA-8XCHT1/E1      JAB104504PN  1.5    Ok

2/0 8xCHT1/E1 SPA               SPA-8XCHT1/E1      JAB104504NG  1.5    Ok

2/1 8xCHT1/E1 SPA               SPA-8XCHT1/E1      JAB104504RG  1.5    Ok

  5  Policy Feature Card 3       WS-F6K-PFC3B       SAL10392XLW  2.3    Ok

  5  MSFC3 Daughterboard         WS-SUP720          SAL10382DBD  2.5    Ok

  6  Policy Feature Card 3       WS-F6K-PFC3B       SAL103938M4  2.3    Ok

  6  MSFC3 Daughterboard         WS-SUP720          SAL10382DF2  2.5    Ok

[Joseph W. Doherty · Accepted solution]

Disclaimer

The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.

Liability Disclaimer

In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.

Posting

"Regular" Ethernet line cards, like your 6548, don't support the QoS features of your SIP200s or FlexWANs line cards.