07-31-2009 11:45 PM - edited 03-04-2019 05:37 AM
How to configure VPLS on ASR 1004 device.Which version ASR support this functionality.
Please provide configuration doc (VPLS ASR)
08-02-2009 10:37 AM
Hi,
VPLS is not supported currently on the ASR1000 but should be in the future.
HTH
Laurent.
04-23-2014 05:53 AM
Excuse me ! ASR 1004 can support VPLS now ?
Looking forward to your reply ,thanks!
04-24-2014 01:31 AM
Hi,
Yes. It is supported now.
-Nagendra
04-24-2014 08:10 PM
Dear Nagendra,
Thanks your reply ! I used this devices to configure VPLS ( 3750--7609 -----ASR 1004 --2950 ), but the VC status is down .I referenced the official configuration and asked my friends ,still couldn't find the reasons. It's the issue of devices compatibility ?
If you have time ,can you help me Analysis the problem ?
Thank you very much !
********************************************
7609:
mpls label protocol ldp
mpls ldp neighbor 10.10.10.102 targeted ldp
mpls ldp discovery hello holdtime 5
mpls ldp discovery targeted-hello accept
mpls ldp router-id Loopback0 force
l2 router-id 10.10.10.101
l2 vfi aaa manual
vpn id 101
neighbor 10.10.10.102 encapsulation mpls
interface Loopback0
ip address 10.10.10.101 255.255.255.255
interface GigabitEthernet5/2 (to 3750)
switchport
switchport access vlan 101
switchport mode access
media-type rj45
speed 100
!
interface GigabitEthernet6/2 (to ASR1004 )
ip address 12.1.1.1 255.255.255.252
media-type rj45
mpls ip
mpls label protocol ldp
!
interface Vlan101
no ip address
xconnect vfi aaa
!
router eigrp 90
network 10.10.10.101 0.0.0.0
network 12.1.1.0 0.0.0.3
!
************************************
ASR1004:
mpls label protocol ldp
mpls ldp neighbor 10.10.10.101 targeted ldp
mpls ldp discovery hello holdtime 5
mpls ldp discovery targeted-hello accept
mpls ldp router-id Loopback0 force
bridge-domain 101
l2 router-id 10.10.10.102
l2 vfi aaa manual
vpn id 101
bridge-domain 101
neighbor 10.10.10.101 encapsulation mpls
interface Loopback0
description test vpls
ip address 10.10.10.102 255.255.255.255
!
interface GigabitEthernet0/0/0 (to 7609)
ip address 12.1.1.2 255.255.255.252
speed 1000
no negotiation auto
mpls ip
mpls label protocol ldp
!
interface GigabitEthernet0/0/1 (to 2950 )
no ip address
speed 100
no negotiation auto
service instance 101 ethernet
encapsulation dot1q 101
bridge-domain 101
!
router eigrp 90
network 10.10.10.102 0.0.0.0
network 12.1.1.0 0.0.0.3
!
********************************
CE configuration like this: access mode
CE1:
interface FastEthernet1/0/1
switchport access vlan 101
switchport mode access
end
interface Vlan101
ip address 192.168.20.10 255.255.255.0
end
CE2 :
interface FastEthernetF0/1
switchport access vlan 101
switchport mode access
end
interface Vlan101
ip address 192.168.20.20 255.255.255.0
end
*************************************
ASR1004#SHOW MPLs L2transport VC DETail
Local interface: VFI aaa vfi up
Interworking type is Ethernet
Destination address: 10.10.10.101, VC ID: 101, VC status: down
Last error: Remote peer access circuit is down
Output interface: Gi0/0/0, imposed label stack {17}
Preferred path: not configured
Default path: active
Next hop: 12.1.1.1
Create time: 22:24:49, last status change time: 00:00:33
Last label FSM state change time: 21:17:13
Signaling protocol: LDP, peer 10.10.10.101:0 up
Targeted Hello: 10.10.10.102(LDP Id) -> 10.10.10.101, LDP is UP
7609#show mpls l2transport vc detail
Local interface: VFI aaa vfi up
Interworking type is Ethernet
Destination address: 10.10.10.102, VC ID: 101, VC status: down
Last error: MPLS dataplane reported a fault to the nexthop
Output interface: none, imposed label stack {}
Preferred path: not configured
Default path: no route
No adjacency
Create time: 1d12h, last status change time: 21:18:20
Last label FSM state change time: 00:00:40
Signaling protocol: LDP, peer 10.10.10.102:0 up
Targeted Hello: 10.10.10.101(LDP Id) -> 10.10.10.102, LDP is UP
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide