Dear Experts, We have 6 sites and plan to connect with 2X ISR4451-X/K9 as Transit Control Plane for SD Access transit. Are there DNA licenses required for the said routers or part number is enough? Regards,Bernard
-
-
-
-
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community
-
Forum Posts
Dears, I need to know the restriction to design multi-site with ip- transit and the WLC locate in HQ not in the branches What is the delay between Access points and WLC required through the WAN link?Can AP act as WLC in the branch if can't achieve t...
Hi there! I’m Shawn Wargo - Principal TME @ Cisco This discussion is a companion to the BRKCRS-2810 - Cisco SD-Access: Fundamentals - A Look Under the Hood technical session that I created for Cisco Live (multiple events & regions, since 2016-2017). ...
Resolved! Access Point Migration
Hi All, When migrating existing APs to an SDA fabric using OTT only (no requirement to migrate to fabric enabled wireless), is it mandatory for the APs to be associated to the in-built Infra VN or can they be associated to a user-configurable VN? Th...
Resolved! Border Node Redundancy
I have the attached external border topology. For the underlay network we have a link between each border node and each fusion switch and a single link between border nodes. There is an eBGP adjacency over each of the border to fusion links (4 in tot...
Resolved! External Border Redundancy
I have the attached external border topology. For the underlay network we have a link between each border node and each fusion switch and a single link between border nodes. There is an eBGP adjacency over each of the border to fusion links (4 in tot...
i am getting the following error when adding a new switch to the fabric (migration status can't be alerted , please check the pay-load) note that : maglev can reach the new switch and DNA can provision it , error appeared when add to fabric only.
Adding a windows-based SFTP host to DNAC failed. "No Permission..." warning at UI. In contrast a SFTP session could be established from the maglev CLI to the SFTP host successfully.Whats different between DNA App and CLI behavior for SFTP connection...
Dear community, we are currently planning the implementation of SDA as a counterpart to our ACI Fabric. Right now we are asking ourselves the question where we can place the DNA Center and ISE? Would you place the appliance inside or outside the ACI ...
We are in planning with our customer to build a giant SD Access Fabric. They have many sites scattered around the local regions. Some sites are large enough to have fabric border/ control node + Fabric Edges and some small sites will have only one to...
Hi Experts, How can we support Meraki over the top of an SD-A deployment ?When we use Meraki L3 roaming, traditionally we'll use MX concentrator, but when we use it with SDA, do we still need MX concentrator ? If not, how would the L3 roaming work...
Resolved! Fabric Border L3 Hand-off Infra_VN
Hi All, I have been reading the SDA fabric deployment guide and have a question regarding automated border L3 hand-off for the infra_VN https://www.cisco.com/c/dam/en/us/td/docs/solutions/CVD/Campus/sda-fabric-deploy-2019oct.pdf As detailed in this ...
I am studying for the ENCOR exam, and I am working on SD-Access. I understand that (correct me if I'm wrong) the physical layer of the SD-Access fabric consists of the network devices. Here is the excerpt that confuses me: "Cisco access layer switche...
Resolved! SD-access switch removal
Hi,I would like to remove an Edge node switch from my Fabric but also from my inventory.I know that DNA Center is very sensitive (bugs, errors when it is not properly done). I have defined these steps :1 - In License Manager part : deregister the swi...
Resolved! On which ise node enable pxgrid ?
HelloIn a 2 nodes ise deployment where should I enable pxgrid to use with DNAC? Only on the primary PAN or on both nodes?If in both nodes does it make sense to have a single certificate for both ? Thank you
