08-29-2016 02:13 PM
Can you have a single identical HBA initiator in different zones on an MDS with different targets in each zone? or can an initiator only log in under one zone?
Is below allowed on the same MDS also the same vsan?
zone name VM005_S05_C1_TO_VNX5300_SPA0_SPA1_SPB0_SPB1 vsan 10
member pwwn 20:01:b4:e1:0f:28:02:0d init
! [VM005_S05_C1]
member pwwn 50:06:01:60:3e:e0:2a:f2 target
! [VNX5300_SPA0]
member pwwn 50:06:01:61:3e:e0:2a:f2 target
! [VNX5300_SPA1]
member pwwn 50:06:01:68:3e:e0:2a:f2 target
! [VNX5300_SPB0]
member pwwn 50:06:01:69:3e:e0:2a:f2 target
! [VNX5300_SPB1]
zone name VM005_S05_C1_TO_VNX5400_SPA2_SPB2 vsan 10
member pwwn 20:01:b4:e1:0f:28:02:0d init
! [VM005_S05_C1]
member pwwn 50:06:01:62:36:e0:14:2d target
! [VNX5400_SPA2]
member pwwn 50:06:01:6a:36:e0:14:2d target
! [VNX5400_SPB2]
Solved! Go to Solution.
08-30-2016 06:42 AM
So you are using device alias ? correct ?
Do you use enhanced zoning ?
May you should do a
"commit vsan 10"
and finally you also have to activate the zonset !
btw. do you see any error messages, while pasting this list of 5300 zones ?
PS.
Have a look at "show running" and you see how zones and zoneset are configured and enabled
08-29-2016 07:01 PM
HI, Steven Williams:
what's wrong with you ? about zone, according to best practices , cisco advise the zone include
single initiator and many target . no problem with you design , i think.
08-30-2016 06:08 AM
I just cant get the blade HBA able to see both targets with this setup so thats why i thought it was a supported design.
08-30-2016 06:28 AM
Please just show us the output of
Show zoneset active vsan 10
Maybe the second target didn't do a flogi ?
I can't see any reason why single initiator - multiple target works, and single initiator - single target not ?
08-30-2016 06:35 AM
ummmm i think i see the issue.....
zoneset name MID_PROD_DR vsan 10
member MIDPVMW001_S01_C1_TO_MIDVNX5400_SPA2_SPB2
member MIDPVMW002_S02_C1_TO_MIDVNX5400_SPA2_SPB2
member MIDPVMW003_S03_C1_TO_MIDVNX5400_SPA2_SPB2
member MIDPVMW004_S04_C1_TO_MIDVNX5400_SPA2_SPB2
member MIDPVMW005_S05_C1_TO_MIDVNX5400_SPA2_SPB2
member MIDPVMW006_S06_C1_TO_MIDVNX5400_SPA2_SPB2
member MIDPVMW007_S07_C1_TO_MIDVNX5400_SPA2_SPB2
member MIDPVMW008_S08_C1_TO_MIDVNX5400_SPA2_SPB2
I dont see my 5300 zone sets in this list.....but i paste this command and they dont add.
zoneset name MID_PROD_DR vsan 10
member MIDPVMW005_S05_C1_TO_MIDVNX5300_SPA0_SPA1_SPB0_SPB1
member MIDPVMW006_S06_C1_TO_MIDVNX5300_SPA0_SPA1_SPB0_SPB1
member MIDPVMW007_S07_C1_TO_MIDVNX5300_SPA0_SPA1_SPB0_SPB1
member MIDPVMW008_S08_C1_TO_MIDVNX5300_SPA0_SPA1_SPB0_SPB1
so whats the issue here.....
08-30-2016 06:42 AM
So you are using device alias ? correct ?
Do you use enhanced zoning ?
May you should do a
"commit vsan 10"
and finally you also have to activate the zonset !
btw. do you see any error messages, while pasting this list of 5300 zones ?
PS.
Have a look at "show running" and you see how zones and zoneset are configured and enabled
08-30-2016 06:53 AM
that was it. They dont show in the zoneset list until the zone is reactivated...boo
Thanks guys!
08-30-2016 07:34 AM
Ok still not working. I see this from the show zoneset active vsan 10
zone name MIDPVMW007_S07_C1_TO_MIDVNX5400_SPA2_SPB2 vsan 10
* fcid 0x200800 [pwwn 20:01:b4:e1:0f:28:02:27] [MIDPVMW007_S07_C1] init
* fcid 0x200000 [pwwn 50:06:01:62:36:e0:14:2d] [MIDVNX5400_SPA2] target
* fcid 0x200100 [pwwn 50:06:01:6a:36:e0:14:2d] [MIDVNX5400_SPB2] target
zone name MIDPVMW008_S08_C1_TO_MIDVNX5400_SPA2_SPB2 vsan 10
* fcid 0x200900 [pwwn 20:01:b4:e1:0f:28:02:34] [MIDPVMW008_S08_C1] init
* fcid 0x200000 [pwwn 50:06:01:62:36:e0:14:2d] [MIDVNX5400_SPA2] target
* fcid 0x200100 [pwwn 50:06:01:6a:36:e0:14:2d] [MIDVNX5400_SPB2] target
zone name MIDPVMW006_S06_C1_TO_MIDVNX5300_SPA0_SPA1_SPB0_SPB1 vsan 10
* fcid 0x200700 [pwwn 20:01:b4:e1:0f:28:02:1a] [MIDPVMW006_S06_C1] init
pwwn 50:06:01:60:3e:e0:2a:f2 [MIDVNX5300_SPA0] target
pwwn 50:06:01:61:3e:e0:2a:f2 [MIDVNX5300_SPA1] target
pwwn 50:06:01:68:3e:e0:2a:f2 [MIDVNX5300_SPB0] target
pwwn 50:06:01:69:3e:e0:2a:f2 [MIDVNX5300_SPB1] target
zone name MIDPVMW007_S07_C1_TO_MIDVNX5300_SPA0_SPA1_SPB0_SPB1 vsan 10
* fcid 0x200800 [pwwn 20:01:b4:e1:0f:28:02:27] [MIDPVMW007_S07_C1] init
pwwn 50:06:01:60:3e:e0:2a:f2 [MIDVNX5300_SPA0] target
pwwn 50:06:01:61:3e:e0:2a:f2 [MIDVNX5300_SPA1] target
pwwn 50:06:01:68:3e:e0:2a:f2 [MIDVNX5300_SPB0] target
pwwn 50:06:01:69:3e:e0:2a:f2 [MIDVNX5300_SPB1] target
why do the ones working have a *fcid in front of them and the ones not working dont?
08-30-2016 10:07 AM
This means, that the pwwn without a * in front, have not done a flogi
pwwn 50:06:01:60:3e:e0:2a:f2 [MIDVNX5300_SPA0] target
pwwn 50:06:01:61:3e:e0:2a:f2 [MIDVNX5300_SPA1] target
pwwn 50:06:01:68:3e:e0:2a:f2 [MIDVNX5300_SPB0] target
pwwn 50:06:01:69:3e:e0:2a:f2 [MIDVNX5300_SPB1] target
and
pwwn 50:06:01:60:3e:e0:2a:f2 [MIDVNX5300_SPA0] target
pwwn 50:06:01:61:3e:e0:2a:f2 [MIDVNX5300_SPA1] target
pwwn 50:06:01:68:3e:e0:2a:f2 [MIDVNX5300_SPB0] target
pwwn 50:06:01:69:3e:e0:2a:f2 [MIDVNX5300_SPB1] target
I cannot tell you why ?
08-30-2016 10:32 AM
I figured it out. The wrong SP ports were connected to the SAN. 3 days of my life gone!
08-29-2016 11:04 PM
Hi Steven
This is ok !
However, most storage vendors (IBM, EMC, HDS, NetApp...) prefer and recommend single initiator - single target zoning.
Walter.
08-30-2016 06:13 AM
Ya i read that alot, but then why is there smart zoning lol.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide