Hello All!
I just had a quick question regarding the upgrade procedures for migrating from a SUP2 to a SUP2A in the MDS 9509 chassis. The procedures seem very straightforward (we have already staged the SUP2As with the identical version of NX...
Dear Everyone, We connect UCS Rack Mount Server's MLOM card to Nexus 5672 using FCoE.When we check fabric login in Nexus switch,we cannot found fabric login from server side.When we use "show interface vfc1 trunk vsan 100", it display "waiting ...
We have a set of MDS's that were configured many moons ago using the GUI software so therefore everything inside the CLI configuration is just a lot of pwwn values. I have added both device-alias's and fcalias's in the MDS config and still so not see...
Can you have a single identical HBA initiator in different zones on an MDS with different targets in each zone? or can an initiator only log in under one zone?
Is below allowed on the same MDS also the same vsan?
zone name VM005_S05_C1_TO_VNX5300_S...
Hi,
A few minutes ago checking something into our switches I realize that we have two different system versions, what is the "real one"???
CNA252040RSAN# sh hardwareCisco Nexus Operating System (NX-OS) SoftwareTAC support: http://www.cisco.com/tacDoc...
HI
Im new and im really in a bad situation.
I have a scenario where i have to deploy a Nexus -switch (5548UP)
I have never worked on this product and really don't know what are the things i have to configure !!!!
Can anyone share some examples using...
Sooo.. what's the point of device aliases again?
After creating a few zones, I noticed in my VNX that it doesn't enumerate the ports the way I thought it would. Port 0 of slot 2 in SPA shows as "A-4", whereas I had made a domain alias called "A2P0...
Hi All Distinguished Members ,
I am working on on Data Center Project on Storage Arrays , but recently i have received a Project for Fabric Services to be migrated from Brocade to Cisco .
1. Brocade to Cisco
2. McData to Cisco
I have never done th...
One of the two interfaces on stuck at init and never comes up
switch is MDS9250i running 6.2(15) with 10G SFPs.
IPStorage1/1 init x.x.x.x/25 10 Gbps 2300IPStorage1/2 up x.x.x.x/25 10 Gbps 2300
have tried restting the port and reloading the module...
Hi All,
Using 4 FC ports on RPA and 4 FC ports of Xtremio Array , we have to connect both of these to Fabric Interconnect.
Question how to do zoning ?
Infrastructure :-
1. RPA is EMC Product . (It can act as both Host and target)
2. XtremIO is EMC...
Can the Cisco UCS Virtual Interface Card 1225 be configured as an iSCSI storage adapters in VMware 6.0
Currently the VIC 1225 is only listed as FCoE storage adapters and the switch and storage don't support FCoE (bummer).
I know it does support "boot...
I had below configurations at my Cisco switches:
1. Cisco switch 1:vsan 1 and vsan9
2. Cisco switch 2:vsan 1 and vsan9
Vsan1 of switch1, operation of all ports:notrunk, vsan9 of switch1, operation:trunk, the port is trunking and connected to switch2...
We recently purchased 2 Cisco SAN switch. Configuration portion is remaining in client's side. I haven't used it yet. Need ideas for fresh installment.
They already have 2 SAN storage, 4 physical servers and they want SAN on HA.
We have licence for 1...
HI,
I'm new to the world of Cisco MDS fabric switches. I am interested in hearing what the experienced users like to save and document for disaster recovery purposes. Our environment consists of two fabrics each with a single 9148S switch. Since ...
The install guide says this...
After the Open Virtual Appliance is deployed, a Deployment Completed Successfully message appears.
Step 3 On the Summary tab in the vSphere Client, review the information about the VM and make note of the IP address.
...
