1941 Router Rommon Mode recory problem (Interface GE 0 link down)

afroz khan · ‎10-07-2013

Dear Friend,

i am try to recover my Router (1941 with serial Card) from rommon mode prosses is below but problem is there showing error (Interface GE 0 link down) i am also try with both cable like cross and streght but problem is still there Note :- Ge0/0 prot was up in Boot time i have also attach Router Log file in atach file

rommon 1 > IP_ADDRESS=192.168.1.1

rommon 2 > IP_SUBNET_MASK=255.255.255.0

rommon 3 > DEFAULT_GATEWAY=192.168.1.1

rommon 4 > TFTP_SERVER=192.168.1.32

rommon 5 > TFTP_FILE=c1700-k9sv8y7-mz.122-15.T14.bin

rommon 6 > tftpdnld

IP_ADDRESS: 192.168.1.1

IP_SUBNET_MASK: 255.255.255.0

DEFAULT_GATEWAY: 192.168.1.1

TFTP_SERVER: 192.168.1.32

TFTP_FILE: c1700-k9sv8y7-mz.122-15.T14.bin

TFTP_MACADDR: e0:5f:b9:a2:69:a0

TFTP_DESTINATION: flash0:

GE_PORT: Ge0/0

TFTP_MEDIA_TYPE: Copper

TFTP_VERBOSE: Progress

TFTP_RETRY_COUNT: 18

TFTP_TIMEOUT: 7200

TFTP_CHECKSUM: No

GE_SPEED_MODE: 1000MB/FULL

Invoke this command for disaster recovery only.

WARNING: all existing data in all partitions on flash will be lost!

Do you wish to continue? y/n: [n]: y

Interface GE 0 link down

TFTP: Operation terminated prematurely.

afroz khan · ‎10-07-2013

I have also try with new Image file

(c1900-universalk9-mz.SPA.152-4.M4.bin)

rommon 1 > IP_ADDRESS=192.168.1.1
rommon 2 > IP_SUBNET_MASK=255.255.255.0
rommon 3 > DEFAULT_GATEWAY=192.168.1.1
rommon 4 > TFTP_SERVER=192.168.1.32
rommon 5 > TFTP_FILE=c1900-universalk9-mz.SPA.152-4.M4.bin

rommon 6 > tftpdnld

          IP_ADDRESS: 192.168.1.1
      IP_SUBNET_MASK: 255.255.255.0
     DEFAULT_GATEWAY: 192.168.1.1
         TFTP_SERVER: 192.168.1.32
           TFTP_FILE:c1900-universalk9-mz.SPA.152-4.M4.bin

TFTP_MACADDR: e0:5f:b9:a2:69:a0
    TFTP_DESTINATION: flash0:
             GE_PORT: Ge0/0
     TFTP_MEDIA_TYPE: Copper
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
       GE_SPEED_MODE: 1000MB/FULL

Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash will be lost!
Do you wish to continue? y/n: [n]: y

Interface GE 0 link down
TFTP: Operation terminated prematurely.

Sandeep Choudhary · ‎10-07-2013

Hi ,

I was having same problem to load the IOS, I think it will be good for you to load ios from xmodem.

http://www.cisco.com/en/US/products/hw/routers/ps259/products_tech_note09186a008015bfac.shtml

Step 1: rommon 12 > xmodem -cfs115200 c1900-universalk9-mz.SPA.152-4.M4.bin

Step2 :Select Transfer and Send File from the HyperTerminal menu bar. (see the link)

it will take long time

Regards

afroz khan · ‎10-11-2013

Dear ,

I Have try with Xmodem prosses but problem is still there

NOTE:- Router Model 1941

Leo Laohoo · ‎10-07-2013

Afroz,

This is a DUPLICATE thread to this.

As I have pointed this out to you in your other thread, you are trying to load an IOS for a 1700 router into your 1900 router.

And this, I can assure you, will not work.

NOTE: You will be able to copy the file into the 1900 router but that's where it ends.

afroz khan · ‎10-08-2013

Dear Leo Laohoo

I Habe try with

c1900-universalk9-mz.SPA.152-4.M4.bin but problem is still there problem with Ge0/0 port wich is taken by default

but when we try to give ip by below mention method but ge0 port is not coming Up

rommon 1 > IP_ADDRESS=192.168.1.1
rommon 2 > IP_SUBNET_MASK=255.255.255.0
rommon 3 > DEFAULT_GATEWAY=192.168.1.1
rommon 4 > TFTP_SERVER=192.168.1.32
rommon 5 > TFTP_FILE=c1900-universalk9-mz.SPA.152-4.M4.bin

rommon 6 > tftpdnld

          IP_ADDRESS: 192.168.1.1
      IP_SUBNET_MASK: 255.255.255.0
     DEFAULT_GATEWAY: 192.168.1.1
         TFTP_SERVER: 192.168.1.32
           TFTP_FILE:c1900-universalk9-mz.SPA.152-4.M4.bin

TFTP_MACADDR: e0:5f:b9:a2:69:a0
    TFTP_DESTINATION: flash0:
             GE_PORT: Ge0/0
     TFTP_MEDIA_TYPE: Copper
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
       GE_SPEED_MODE: 1000MB/FULL

Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash will be lost!
Do you wish to continue? y/n: [n]: y

Interface GE 0 link down
TFTP: Operation terminated prematurely.

johnlloyd_13 · ‎10-08-2013

hi,

i think you should set your DEFAULT_GATEWAY and TFTP_SERVER to be on same IP address with your PC/laptop.

try to make it simple and use 192.168.1.2. using a straight cable should be no problem.

afroz khan · ‎10-11-2013

Dear,

I have given IP Address in below step

Router IP

IP_ADDRESS=192.168.1.1

Subnet Mask

IP_SUBNET_MASK=255.255.255.0

Default Gateway

DEFAULT_GATEWAY=192.168.1.1

PC IP IS

TFTP_SERVER=192.168.1.32

Image File Name

TFTP_FILE=c1900-universalk9-mz.SPA.152-4.M4.bin

Leo Laohoo · ‎10-08-2013

Afroz,

1. Power down the router;

2. Eject the CF;

3. Get a multi-card reader;

4. Use a PC to copy the IOS from your PC to the CF using the multi-card reader;

5. Insert the CF back to the router.

6. Power on the router.

Please don't forget to rate our useful posts.

afroz khan · ‎10-11-2013

Dear ,

Ge0/0 Port is enbelt in Router Mother Board it it not posibale to remove the Ge0/0 Port from the router

resaga · ‎06-16-2014

hi Afroz,

i think that you have problem with speed, be sure that the speed of the network card from the laptop or PC is 1 GB, else you must set speed to 100, with command GE_SPEED_MODE: