02-02-2015 08:53 PM - edited 03-07-2019 10:29 PM
hi all,
i'm trying to configure a few 3650s for PVLAN but it seems it doesn't support it.
it's already configured for VTP transparent mode.
i thought 'newer' switches should already have this feature.
anyone can advise if i need to upgrade IOS or is it a platform restriction?
or is there some command that i need to enable on this kind of switch?
SW#sh vtp status
VTP Version capable : 1 to 3
VTP version running : 1
VTP Domain Name : <SNIP>
VTP Pruning Mode : Disabled
VTP Traps Generation : Disabled
Device ID : 74a2.e665.2200
Configuration last modified by 192.168.1.1 at 0-0-00 00:00:00
Feature VLAN:
--------------
VTP Operating Mode : Transparent <<<
Maximum VLANs supported locally : 1005
Number of existing VLANs : 14
Configuration Revision : 0
MD5 digest : 0xBC 0x96 0x7F 0xE1 0xA8 0x8A 0x1C 0x82
0x1F 0x1C 0x90 0x9A 0x82 0xA7 0xB7 0x9F
SW(config-vlan)(config)#vlan 81
SW(config-vlan)(config-vlan)#?
VLAN configuration commands:
are Maximum number of All Route Explorer hops for this VLAN (or zero
if none specified)
backupcrf Backup CRF mode of the VLAN
bridge Bridging characteristics of the VLAN
exit Apply changes, bump revision number, and exit mode
media Media type of the VLAN
name Ascii name of the VLAN
no Negate a command or set its defaults
parent ID number of the Parent VLAN of FDDI or Token Ring type VLANs
remote-span Configure as Remote SPAN VLAN
ring Ring number of FDDI or Token Ring type VLANs
said IEEE 802.10 SAID
shutdown Shutdown VLAN switching
state Operational state of the VLAN
ste Maximum number of Spanning Tree Explorer hops for this VLAN (or
zero if none specified)
stp Spanning tree characteristics of the VLAN
tb-vlan1 ID number of the first translational VLAN for this VLAN (or zero
if none)
tb-vlan2 ID number of the second translational VLAN for this VLAN (or
zero if none)
SW(config-vlan)#p?
parent
SW(config-vlan)# private-vlan community
^
% Invalid input detected at '^' marker.
SW#sh ve
Cisco IOS Software, IOS-XE Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Version 03.03.04SE RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 29-Aug-14 22:22 by prod_rel_team
Cisco IOS-XE software, Copyright (c) 2005-2014 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0.
(http://www.gnu.org/licenses/gpl-2.0.html) For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: CAT3K_CAA Boot Loader (CAT3K_CAA-HBOOT-M) Version 1.2, RELEASE SOFTWARE (P)
--More--
*Feb 3 04:50:55.883: %SYS-5-CONFIG_I: Configured from console b e
ends10sw06 uptime is 26 minutes
Uptime for this control processor is 28 minutes
System returned to ROM by reload
System image file is "flash:packages.conf"
Last reload reason: reload
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
License Level: Ipbase
License Type: Permanent
Next reload license Level: Ipbase
cisco WS-C3650-48PS (MIPS) processor with 4194304K bytes of physical memory.
Processor board ID FDO1852Exxx
1 Virtual Ethernet interface
52 Gigabit Ethernet interfaces
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
250456K bytes of Crash Files at crashinfo:.
1609272K bytes of Flash at flash:.
0K bytes of Dummy USB Flash at usbflash0:.
0K bytes of at webui:.
Base Ethernet MAC Address : 74:a2:e6:65:22:00
Motherboard Assembly Number : 73-15131-05
Motherboard Serial Number : FDO18530xxx
Model Revision Number : D0
Motherboard Revision Number : A0
Model Number : WS-C3650-48PS
System Serial Number : FDO1852Exxx
Switch Ports Model SW Version SW Image Mode
------ ----- ----- ---------- ---------- ----
* 1 52 WS-C3650-48PS 03.03.04SE cat3k_caa-universalk9 INSTALL
Configuration register is 0x102
02-02-2015 09:03 PM
anyone from TAC could verify this?
it seems it's not supported by this switch.
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3650/software/release/3se/vlan/configuration_guide/b_vlan_3se_3650_cg/b_vlan_3se_3650_cg_chapter_011.html
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3650/software/release/3se/release_notes/OL30563.html
02-03-2015 07:35 AM
I also ran into this issue - but cannot believe that this settled feature is removed ????
02-03-2015 05:47 PM
hi,
i managed to get the PVLAN running on IOS-XE 3.7.
the file is quite big though:
cat3k_caa-universalk9.SPA.03.07.00.E.152-3.E.bin
02-04-2015 03:27 AM
Hello John
I have been working on a PVLAN-solution for the 3850 and the IOS-XE 3.7 for a while (almost same hw/sw).
how did you do the PVLAN, implementation ? (SVI, promiscous, only isolated, isolated and community? routing?) We are using an SVI solution and have a fucking hard time getting the SVIs to speak correctly.
02-03-2015 08:39 AM
Hello
fyi - Looks like IOS-XE doesn't support it
http://https://tools.cisco.com/Support/CLILookup/cltSearchAction.do
res
Paul
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide