3850 Stack and Stack Priority

[alex.roth]

Hi,

Question regarding a Cisco 3850 & Stack .

I´ve two 3850 switches stacked.

sh switch

Switch/Stack Mac Address : c025.5cb9.1b80 - Local Mac Address

Mac persistency wait time: Indefinite

                                             H/W   Current

Switch#   Role    Mac Address     Priority Version  State

------------------------------------------------------------

*1       Active   c025.5cb9.1b80     1      J0      Ready

2       Standby  c025.5cb7.c480     1      J0      Ready

Now I will change the priority from switch 1 from 1 to  15 but I can´t do this:

(config)#switch 1 ?

  provision  Configure Switch provision / offline confi NMTSL3CORE1

I can´t use the command : switch 1 priority  15 as exmaple . Why ?

Thanks for help.

Cheers

[Leo Laohoo]

I can´t use the command : switch 1 priority  15 as exmaple . Why ?

If you can't use the command "switch 1 priority 15" then show us the syntax and the error message.

[alex.roth]

See below :

(config)#switch 1 pr

provision

and

(config)#switch 1 pri?

% Unrecognized command Thx

Thx

[Leo Laohoo]

Can you post the complete output to the command "sh version"?

[alex.roth]

See below :

sh ver
Cisco IOS Software, IOS-XE Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Version 03.03.01SE RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Thu 05-Dec-13 10:15 by prod_rel_team

ROM: IOS-XE ROMMON
BOOTLDR: CAT3K_CAA Boot Loader (CAT3K_CAA-HBOOT-M) Version 1.2, RELEASE SOFTWARE (P)

NMTSL3CORE1 uptime is 2 hours, 57 minutes
Uptime for this control processor is 2 hours, 59 minutes
System returned to ROM by reload at 11:53:48 CET Mon Dec 16 2013
System image file is "flash:packages.conf"
Last reload reason: reload

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

License Level: Ipbase
License Type: Permanent
Next reload license Level: Ipbase

cisco WS-C3850-24P (MIPS) processor with 4194304K bytes of physical memory.
Processor board ID FOC1737X0T4
4 Virtual Ethernet interfaces
56 Gigabit Ethernet interfaces
8 Ten Gigabit Ethernet interfaces
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
250456K bytes of Crash Files at crashinfo:.
250456K bytes of Crash Files at crashinfo-2:.
1609272K bytes of Flash at flash:.
1609272K bytes of Flash at flash-2:.
0K bytes of Dummy USB Flash at usbflash0:.
0K bytes of Dummy USB Flash at usbflash0-2:.
0K bytes of  at webui:.

Base Ethernet MAC Address          : c0:25:5c:b9:1b:80
Model Revision Number              : J0
Motherboard Revision Number        : C0
Model Number                       : WS-C3850-24P

Switch Ports Model              SW Version        SW Image              Mode
------ ----- -----              ----------        ----------            ----
*    1 32    WS-C3850-24P       03.03.01SE        cat3k_caa-universalk9 INSTALL
     2 32    WS-C3850-24P       03.03.01SE        cat3k_caa-universalk9 INSTALL

Switch 02
---------
Switch uptime                      : 58 minutes
Base Ethernet MAC Address          : c0:25:5c:b7:c4:80
Model Revision Number              : J0
Motherboard Revision Number        : C0
Model Number                       : WS-C3850-24P

Configuration register is 0x102

Cheers

[Leo Laohoo · Accepted solution]

Alex,

Get out of configuration mode.  Switch priority can be done in enable or EXEC mode.

Go here.

[alex.roth]

Hi,

OK, this solution is easy , ... double checked the docu and this correct . It´s just habit to use the conf t mode,

Many thanks ,

[Leo Laohoo]

Someone re-invented the wheel, Alex.

Thanks for taking the time to rate our posts. 

[johnwenhuang]

you should configure it under privileged mode.

SW0701#switch 2 priority 15

[b0032313@my.shu.ac.uk]

john - You are right .