10-28-2009 01:01 PM - last edited on 03-25-2019 04:08 PM by ciscomoderator
I have a 4507 switch with the following:
IOS ver cat4500-entservicesk9-mz.122-52.SG
Sup- WS-X4516-10GE
There are interfaces on the sup card that have a status of "inactive". How can I activate these interfaces? The #hw-module uplink select all command is not there!
10-28-2009 01:22 PM
Hi.
Either the VLAN assigned to these interfaces are not created in the VLAN database. Or there might be something with the number of ports supported - could you post a show module and show interface status?
HTH, Ingolf
10-29-2009 03:34 AM
Below are the requested outputs. Thanks for the help!
#sh module
Chassis Type : WS-C4507R-E
Power consumed by backplane : 40 Watts
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 JAE1242XV6E
3 6 Sup V-10GE 10GE (X2), 1000BaseX (SFP) WS-X4516-10GE JAE1239W7KQ
4 6 Sup V-10GE 10GE (X2), 1000BaseX (SFP) WS-X4516-10GE JAE1239W437
M MAC addresses Hw Fw Sw Status
--+--------------------------------+---+------------+----------------+---------
1 0023.5e6d.a5c0 to 0023.5e6d.a5ef 2.5 Ok
3 0023.33ca.d680 to 0023.33ca.d685 5.1 12.2(31r)SGA 12.2(52)SG Ok
4 0023.33ca.d686 to 0023.33ca.d68b 5.1 12.2(31r)SGA 12.2(52)SG Ok
Mod Redundancy role Operating mode Redundancy status
----+-------------------+-------------------+----------------------------------
3 Active Supervisor SSO Active
4 Standby Supervisor SSO Standby hot
#sh int status
Port Status Vlan Duplex Speed Type
Te3/1 connect 9 full 10G No X2
Te3/2 inactive 9 full 10G No X2
Gi3/3 connected 316 full 1000 1000BaseLH
Gi3/4 connected trunk full 1000 1000BaseLH
Gi3/5 inactive 9 full 1000 No Gbic
Gi3/6 inactive 9 full 1000 No Gbic
Te4/1 notconnect 1 full 10G No X2
Te4/2 inactive 1 full 10G No X2
Gi4/3 notconnect 1 full 1000 No Gbic
Gi4/4 connected trunk full 1000 1000BaseLH
Gi4/5 inactive 1 full 1000 No Gbic
Gi4/6 inactive 1 full 1000 No Gbic
10-29-2009 04:47 AM
Put gbics in the ports..
10-29-2009 04:54 AM
Thanks for the suggestion, I had tried that already. Unfortunately it did not resolve the problem.
06-29-2010 01:02 AM
Hello, due to the fact you are using a redundant supervisor, some interfaces are disabled
. This is a normal behavior.
You can find on datasheet which combinations are possible
Table 4. Supervisor Engine 6-E High-Availability and Uplink Options
Regards,
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: