11-28-2013 03:41 AM - edited 03-07-2019 04:49 PM
Hi,
after upgrading to 2t supervisor our wism controller is not working properly.
I can connect to it via service ip address but via management I can't.
status is ok, on line diagnostic is ok... but all AP are not working.
on 6509 we are runing
bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin
on wism:
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.240.0
RTOS Version..................................... 7.0.240.0
Bootloader Version............................... 7.0.240.0
Emergency Image Version.......................... 7.0.240.0
Build Type....................................... DATA + WPS
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 16 CEF720 16 port 10GE WS-X6716-10GE
2 6 Firewall Module WS-SVC-FWM-1
3 10 WiSM WLAN Service Module WS-SVC-WISM-1-K9
5 5 Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 f866.f220.08 to f86.f220.07 1.0 12.2(18r)S1 15.1(2)SY Ok
2 0023.3d.e174 to 00.334d.e17b 4.5 7.2(1) 4.1(9) Ok
3 0025.87.d73a to 025.84.d749 2.3 12.2(14r)S5 15.1(2)SY Ok
5 5057.a8.1d to 505a8.1d18 1.5 12.2(50r)SYS 15.1(2)SY Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 Distributed Forwarding Card WS-F6K-DFC4-E 1.2 Ok
3 Centralized Forwarding Card WS-SVC-WISM-1-K9-D 2.1 Ok
5 Policy Feature Card 4 VS-F6K-PFC4 2.1 Ok
5 CPU Daughterboard VS-F6K-MSFC5 2.1 Ok
Mod Online Diag Status
---- -------------------
1 Pass
2 Pass
3 Pass
5 Pass
is there problem with ios incapability or am I doing something wrong.
regards,
Ivan
Solved! Go to Solution.
11-28-2013 03:07 PM
Check your allowed VLAN is enabled on the WiSM1 port channel.
11-28-2013 08:47 AM
Hi,
Your IOS is good, as you have a later version than what is required which is 15.0(1)SY.
what is the output of "sh wism status"?
Have you tried rebooting the switch?
HTH
11-28-2013 03:07 PM
Check your allowed VLAN is enabled on the WiSM1 port channel.
11-29-2013 01:47 AM
Ok i think the problem is in:
Port-channel1 unassigned YES unset down down
Port-channel2 unassigned YES unset down down
WiSM Controller 2 in Slot 3 not configured
Operational Status of the Controller : Oper-Up
Service VLAN : 702
Service Port : 10
Service Port Mac Address : 0023.eb01.c322
Service IP Address : 10.7.2.12
Management IP Address : 10.7.3.20
Software Version : 7.0.240.0
Port Channel Number : 0
WCP Keep Alive Missed : 0
i just need to figure this out :-))
Thx.
11-29-2013 01:59 AM
hi!
find solution:
wism module X controller Y allowed-vlan A,B,C
THX everyone for help!
11-29-2013 02:46 AM
Can you please mark this thread as "Answered"?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide