cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2031
Views
0
Helpful
3
Replies

6509 VSS IOS Upgrade gone bad - kinda

Tonight we were performing an IOS upgrade on our 6509 VSS to 122-33.SXI6.  Both 6509's have dual Supervisor cards installed.  Initially we had problems with switch 2 slot 5 supervisor returning to rommon however switch 2 slot 6 supervisor loaded correctly.  After manually setting the boot var in rommon, switch 2 slot 5 supervisor reloaded correctly.

After all supervisor's were online we noticed when looking at " show switch virtual redundancy" that sw 1 & 2 slot 6 supervisors were running the correct IOS version but sw 1 & 2 slot 5 were running different IOS versions, however when looking at the show version we are running on the upgraded IOS???  See output below...

Does anyone have any ideas why when the active supervisor has loaded the incorrect IOS the VSS is running on the upgraded IOS?  I have verified the IOS was copied correctly to each supervisor bootdisk, I see no issues. 

                  My Switch Id = 1
                Peer Switch Id = 2
        Last switchover reason = none
    Configured Redundancy Mode = sso
     Operating Redundancy Mode = sso

Switch 1 Slot 5 Processor Information :
-----------------------------------------------
        Current Software state = ACTIVE
       Uptime in current state = 3 hours, 38 minutes
                 Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Fri 24-Feb-12 21:38 by prod_rel_team
                          BOOT = sup-bootflash:s72033-ipservicesk9_wan-mz.122-33.SXI5.bin,12;
                   CONFIG_FILE =
                       BOOTLDR =
        Configuration register = 0x2102
                  Fabric State = ACTIVE
           Control Plane State = ACTIVE

Switch 1 Slot 6 Processor Information :
-----------------------------------------------
        Current Software state = RPR-Warm
       Uptime in current state = 3 hours, 37 minutes
                 Image Version = Cisco IOS Software, s72033_lc Software (s72033_lc-SP-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Fri 24-Feb-12 21:38 by prod_rel_team
                         BOOT = bootdisk:s72033-advipservicesk9_wan-mz.122-33.SXI9.bin,1;bootdisk:s72033-ipservicesk9_wan-mz.122-33.SXI6.bin,1;
                   CONFIG_FILE = esk9_wan-mz.122-33.SXI6.bin,1;
                       BOOTLDR =
        Configuration register = 0x2102
                  Fabric State = RPR-Warm
           Control Plane State = RPR-Warm

Switch 2 Slot 5 Processor Information :
-----------------------------------------------
        Current Software state = STANDBY HOT (switchover target)
       Uptime in current state = 1 hour, 13 minutes
                 Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Fri 24-Feb-12 21:38 by prod_rel_team
                          BOOT = sup-bootflash:s72033-ipservicesk9_wan-mz.122-33.SXI6.bin,12;sup-bootflash:s72033-ipservicesk9_wan-mz.122-33.SXI5.bin,12;
                   CONFIG_FILE =
                       BOOTLDR =
        Configuration register = 0x2102
                  Fabric State = ACTIVE
           Control Plane State = STANDBY

Switch 2 Slot 6 Processor Information :
-----------------------------------------------
        Current Software state = RPR-Warm
       Uptime in current state = 1 hour, 14 minutes
                 Image Version = Cisco IOS Software, s72033_lc Software (s72033_lc-SP-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Fri 24-Feb-12 21:38 by prod_rel_team
                          BOOT = bootdisk:s72033-advipservicesk9_wan-mz.122-33.SXI9.bin,1;bootdisk:s72033-ipservicesk9_wan-mz.122-33.SXI6.bin,1;
                   CONFIG_FILE = esk9_wan-mz.122-33.SXI6.bin,1;
                       BOOTLDR =
        Configuration register = 0x2102
                  Fabric State = RPR-Warm
           Control Plane State = RPR-Warm

####Show Version

Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Fri 24-Feb-12 21:38 by prod_rel_team

ROM: System Bootstrap, Version 12.2(17r)SX5, RELEASE SOFTWARE (fc1)

LRDC-6509-VSS uptime is 3 hours, 40 minutes
Uptime for this control processor is 3 hours, 41 minutes
Time since LRDC-6509-VSS switched to active is 3 hours, 39 minutes
System returned to ROM by reload at 02:35:34 CDT Wed May 16 2012 (SP by reload)
System restarted at 02:39:53 CDT Wed May 16 2012
System image file is "sup-bootdisk:s72033-advipservicesk9_wan-mz.122-33.SXI9.bin"
Last reload reason: Reload Command

3 Replies 3

Leo Laohoo
Hall of Fame
Hall of Fame

Can you please post the output to the command "sh run b | b boot-start-marker"?

boot-start-marker

boot system flash sup-bootdisk:s72033-advipservicesk9_wan-mz.122-33.SXI9.bin

boot system flash sup-bootdisk:s72033-ipservicesk9_wan-mz.122-33.SXI6.bin

boot-end-marker

Ok.  That's weird.

Unless someone's going to correct me, I'm suspecting this is an IOS bug.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Review Cisco Networking products for a $25 gift card